Intel SRCU32 - RAID Controller Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 182

background image

47

3 Installing Microsoft Windows NT or

Windows 2000

This section covers installation issues related to the Microsoft Windows NT and Windows 2000
operating systems. For a successful installation, study the Windows NT/2000 system manuals
thoroughly. The required Intel RAID Controller SRCU32 disks can be created from the Intel RAID
Controller SRCU32 system CD-ROM.

Operating System Installation Procedures

✏

✏

✏

✏

NOTE

Begin the installation process in this chapter if you are installing the OS and Intel RAID Controller
SRCU32 or upgrading from the Windows NT OS (the OS is currently installed on a compatible
Intel RAID Controller SRCU32) to Windows 2000.

Your installation falls into one of two categories:

•

Install the OS on either a RAID volume or single disk that is attached to and configured on the
Intel RAID Controller SRCU32 that you are installing,
OR

•

Install the OS on either an IDE hard drive or a SCSI hard drive that is not attached to the Intel
RAID Controller SRCU32 that you are installing

Pre-Installation Requirements Checklist

This section identifies the minimum hardware and software required to successfully install the Intel
RAID Controller SRCU32 and the accompanying software suite.

Minimum Hardware Requirements

✏

NOTE

The Intel RAID Controller SRCU32 will work in a 32-bit, 33 or 64 MHz PCI slot; however, a 64-bit
66 MHz slot is recommended for maximum performance.

•

Computer with CD-ROM drive (not attached to the Intel RAID Controller SRCU32).
Computer must be on the supported hardware list.

•

One available PCI slot.

See note above.

•

PCI 2.2 compliant System BIOS.

•

SCSI hard drive(s) (the minimum required to meet the desired RAID level).

«
...
45
46
47
48
49
...
»

Содержание SRCU32 - RAID Controller























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SRCU32 - RAID Controller

Бренд: Rabbit Страницы: 45

Бренд: Rabbit Страницы: 174

Бренд: Rabbit Страницы: 43

Бренд: LAWO Страницы: 154

LS42 - BladeCenter - 7902

Бренд: IBM Страницы: 56

Бренд: IBM Страницы: 2

BladeCenter Management Module

Бренд: IBM Страницы: 78

Бренд: IBM Страницы: 110

Remote Supervisor Adapter II

Бренд: IBM Страницы: 132

Transportation FiberinMotion

Бренд: Radwin Страницы: 122

Бренд: Gate Страницы: 8

Elite Controller

Бренд: RANA Systems Страницы: 328

HIRESCHMANN IT MAMMUTHUS MTM8003-FAN

Бренд: Belden Страницы: 84

Mercury FireWire 400

Бренд: OWC Страницы: 2

Бренд: ZALMAN Страницы: 8

Бренд: Alarm Страницы: 5

Disc Publisher XR

Бренд: Primera Страницы: 2

Бренд: S&T Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды