Intel SRCU32 - RAID Controller Скачать руководство пользователя страница 175 | Manualshive

Страница: 175 / 182

background image

Regulatory and Certification Information

175

Electromagnetic Compatibility Notices

FCC Verification Statement (USA)

Product Type: GDT8623RZ-I (Intel RAID Controller SRCU32)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

Intel Corporation
5200 N.E. Elam Young Parkway
Hillsboro, OR 97124-6497
Phone: 1-800-628-8686

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the grantee of this device could void the
user’s authority to operate the equipment. The customer is responsible for ensuring compliance of
the modified product.

All cables used to connect to peripherals must be shielded and grounded. Operation with cables,
connected to peripherals that are not shielded and grounded may result in interference to radio and
TV reception.

«
...
173
174
175
176
177
...
»

Содержание SRCU32 - RAID Controller























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SRCU32 - RAID Controller

Бренд: NAIM Страницы: 2

Бренд: Jetter Страницы: 35

Бренд: Lattice Semiconductor Страницы: 15

Transportation FiberinMotion

Бренд: Radwin Страницы: 122

Compact Emulator M30620T-CPE

Бренд: Renesas Страницы: 52

Бренд: Teac Страницы: 20

cMT-FHDX Series

Бренд: Maple Systems Страницы: 2

Бренд: NETGEAR Страницы: 2

Бренд: Lanner Страницы: 78

Бренд: Z3 Technology Страницы: 87

Бренд: Logicube Страницы: 56

EK-FC750 GTX Series

Бренд: ekwb Страницы: 2

Бренд: 3Com Страницы: 53

Бренд: FiberHome Страницы: 2

Бренд: ETAS Страницы: 36

Бренд: ST Страницы: 67

Бренд: Wistron NeWeb Страницы: 32

Бренд: SilverStone Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды