Intel SRCU32 - RAID Controller Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 182

background image

63

5 Installing Novell Netware

This section discusses installation issues related to the Novell NetWare operating system and
covers versions NetWare 4.2 and NetWare 5.1. For a successful installation, study the NetWare
system manuals thoroughly. The information provided in this section refers to the loading of the
Intel RAID Controller SRCU32 NetWare driver(s) only. The required Intel RAID Controller
SRCU32 disks can be created from the Intel RAID Controller SRCU32 system CD-ROM.

Pre-Installation Requirements Checklist

This section identifies the minimum hardware and software required to successfully install the Intel
RAID Controller SRCU32 and the accompanying RAID Software Suite.

Minimum Hardware Requirements

✏

NOTE

The Intel RAID Controller SRCU32 will work in a 32-bit, 33 or 64 MHz PCI slot; however, a 64-bit
66 MHz slot is recommended for maximum performance.

•

Computer with CD-ROM drive (not attached to the Intel RAID Controller SRCU32). The
computer must be on the supported hardware list (for example, Intel SCB2 server board).

•

One available PCI slot.

See note above.

•

PCI 2.2 compliant System BIOS.

•

SCSI hard drive(s) (the minimum required to meet the desired RAID level).

Minimum Software Requirements

•

RAID Software Suite CD-ROM

•

20 MB of hard drive space

•

RAID Driver Installation Diskette for NetWare

•

Novell NetWare 4.2 or 5.1 Software

«
...
61
62
63
64
65
...
»

Содержание SRCU32 - RAID Controller























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SRCU32 - RAID Controller

Бренд: XDS Страницы: 99

Бренд: GE Страницы: 6

Ray 3 Plus Client

Бренд: Sun Microsystems Страницы: 6

Бренд: dbx Страницы: 2

Бренд: dbx Страницы: 17

Бренд: ICP DAS USA Страницы: 14

Бренд: ICP DAS USA Страницы: 25

Бренд: ICP DAS USA Страницы: 15

Бренд: ICP DAS USA Страницы: 8

Бренд: Dahua Страницы: 6

Бренд: iCEBOX Страницы: 57

PSoC 4 S Series

Бренд: Cypress Страницы: 4

Бренд: AXIOMTEK Страницы: 2

Бренд: UNICORECOMM Страницы: 19

Бренд: ASROCK Страницы: 173

Бренд: Rosewill Страницы: 2

Бренд: Qlogic Страницы: 2

Бренд: Renesas Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды