Page 19
Option 6
Pendant Chirps for Disarm to output
- This option will map four short pulses (Chirps) to the output
when Area "A" is Disarmed via a radio key (Pendant) ,( the length of the pulses is set by the pulse
timer P221E-P228E).
Option 7
Pulse on Arming to output
- This option will map a pulse to the Output each time Area"A" is armed
( the length of the pulses is set by the pulse timer P221E-P228E).
Option 8
Pulse on Disarming to output
- This option will map a pulse to the Output each time Area"A" is
disarmed ( the length of the pulses is set by the pulse timer P221E-P228E).
Note: P112E through P118E are as above but applied to outputs 2-8
PARTITION
“
B
”
OPTIONS
PARTITION
“
B
”
OPTIONS - P120E
This address allows modification of how Partition
“
B
”
arming, monitor and control keys work at the keypad.
P120E 1E
“
ARM
”
button required before code to set- Default off
2E
“
MONITOR
”
button required before code to turn on Monitor Mode- Default off
3E
“
CODE
”
required to arm- Default off
4E
“
ARM
”
button can disarm system during exit delay- Default on
5E
“
MONITOR
”
button can disarm Monitor Mode at any time- Default on
6E
No Exit Beeps to keypads in Monitor Mode- Default off
7E
Key-switch Enabled- Default off
8E
Key-switch Mode- Default off
Option 1
“
ARM
”
button required before code to set
- This option determines if the
“
ARM
”
button must be
pressed before a code is entered to set Area
“
B
”
. If a keypad is assigned to both Partitions, this
option should be set to allow individual arming of each area. This option disables the Arm button from
disarming during the exit delay.
Option 2
“
MONITOR
”
button required before code to set
- This option determines if the
“
MONITOR
”
button
must be pressed before a code is entered to set Area
“
B
”
Monitor Mode. If a keypad is assigned to
both Partitions, this option should be set to allow individual arming of Monitor Mode for each area.
Option 3
“
CODE
”
required to set
- If this option is set, the
“
ARM
”
button is disabled and the panel requires a
code to arm as well as disarm.
Option 4
“
ARM
”
button can disarm during exit delay
- If this option is on then the
“
arm
”
button can disarm
Partition
“
B
”
during the exit delay time with a single press of the button. If the option is off then the
alarm can only be unset by a valid code, even during the exit delay time.
Option 5
“
MONITOR
”
button can disarm Monitor Mode
- This option allows the
“
Monitor
”
button to disarm
monitor mode at any time (including when Monitor Mode is fully set). If the option is off then Monitor
Mode can only be unset by a valid code. This feature is defaulted to keypad addresses 1 & 4 ( 4
being the default address for the monitor key station).
Option 6
No Exit Beeps to keypads in Monitor Mode -
This option stops the exit beeps from occurring at all
keypads when Monitor Mode is set. Normally used for silent night arming.
Option 7
Enable Partition
“
B
”
Key-switch -
If this option is turned on then the system tamper input (Tmp)
becomes a Dual End of Line Input (Refer to Type 4 drawing on Page 5 for wiring details). The high
input 8K2 is reserved for Partition
“
B
”
key-switch operation. An open circuit will still be seen as a
system tamper.
Option 8
Key-switch Mode -
If this option is On then the key-switch has a toggle function (ie the arm/disarm
state will follow the key-switch state). If Off then the key-switch is momentary (ie each single pulse
will change the arm/disarm state). The panel tamper input is used to provide the key-switch function.
Содержание Elite Version 8D
Страница 56: ...Page 56 ...
