Intek Elite Version 8D страница 25 Скачать руководство пользователя

Страница: 25 / 56

Page 25

Option 3

Crow Merlin PIR (unsupervised) -

If a Crow Merlin radio PIR is used on the Elite radio zone input,

setting this bit allows the panel to correctly recognize the alarm, tamper & battery low signal from the
device. The automatic supervised signal sent every 40 minutes by the PIR is ignored in this mode.

Option 4

Crow Merlin PIR (supervised) -

If a Crow Merlin radio PIR is used on the Elite radio zone input,

setting this bit allows the panel to correctly recognize the alarm, tamper & battery low signal from the
device. Setting this option on also starts a 4 hour timer for the supervised signal. The 4 hour timer is
constantly being reset while valid supervised signals are being received every 40 minutes. If no
supervised signals are received from the PIR within the 4 hour period, a supervised alarm is
generated.

Option 11

Ness Battery Low

- If a Ness radio pendant or PIR is used on the Elite radio zone input, setting this

bit allows the panel to correctly recognize the battery low signal from Ness devices.

Option 12

Ness Radio Reed Switch

- If a Ness radio reed switch is used on the Elite radio zone input, setting

this bit allows the panel to correctly recognize the battery low signal from Ness device. This bit also
recognizes the open and closed signals from the reed switch so the zone Led can follow the correct
state of the reed switch (ie open or closed)

Option 21

Electronics Line Radio PIR-

If an Electronics Line radio PIR is used on the Elite radio zone input,

setting this bit allows the panel to correctly recognize the alarm, tamper & battery low signal from EL
device.

Option 31

Visonic Radio PIR-

If a Visonic K900 radio PIR is used on the Elite radio zone input, setting this bit

allows the panel to correctly recognize the alarm, tamper & battery low signal from the device.

Option 32

Visonic Powercode (unsupervised) -

If a Visonic Powercode radio device is used on the Elite

radio zone input, setting this bit allows the panel to correctly recognize the alarm and battery low
signal from the device but the supervised signal is ignored.

Option 33

Visonic Powercode (supervised) -

If the Visonic Powercode range of radio PIR or reed switch are

used on the Elite radio zone input, setting this bit allows the panel to correctly recognize the alarm,
tamper & battery low signal from the device. Setting this option on also starts a 4 hour timer for the
supervised signal. The 4 hour timer is constantly being reset while valid supervised signals are being
received every 1-1.5 hours. If no supervised signals are received from the PIR within the 4 hour
period, a supervised alarm is generated.

Note: P232E through P238E are as above but applied to zones 2-8

RADIO ZONE SUPERVISED TIMER

P239E RADIO ZONE SUPERVISED TIMER

Default= 240 Minutes (Value 0-255 Minutes)

RADIO PENDANT CODE LOAD

To  load  a  radio  pendant  on  the  panel,  press  the  appropriate  address  number  (e.g.  P614E  for
Pendant  4).  The  keypad  buzzer  will  beep  once  a  second  to  indicate  learn  mode  has  been  initiated
and the Led on the RX-16 board will flash. The radio pendant you wish to load must transmit a signal
within  30  seconds  of  entering  learn  mode  otherwise  the  panel  will  time  out  and  no  code  will  be
loaded. If a valid code is received within the 30 seconds the keypad will give 3 short beeps and exit
learn  mode.  To  remove  a  loaded  radio  pendant  at  a  single  address  only,  enter  in  the  code  load
address as above eg P614E, then without operating the transmitter and before the 30 second timer
expires press the

“

Enter

”

button. This will remove the code loaded against this address (in this case

radio pendant 4).

P611E

Load Radio Pendant # 1

P612E

Load Radio Pendant # 2

P613E

Load Radio Pendant # 3

P614E