InSinkErator GN1100, Руководство по установке

Страница: 4 / 46

Scalding Hazard: Do not allow
water to boil. May result in
severe burns.
■ ■
Only use mild cleaners to clean the tap and
plastic components.
■ ■
Cleaners with acids, abrasives, alkaline, and
organic solvents will result in deterioration
of the plastic components and void
the warranty.
CLEANING THE TAP AND TANK
Anytime the steaming hot water tap is not used for
extended periods of time, unplug and drain unit.
If it is below freezing you will need to unplug the
unit and drain it.
■ ■
Disconnect power from unit.
■ ■
Push hot water tap lever and allow water
to flow until it is cool.
■ ■
Shut the cold water tap off at the valve.
■ ■
Remove drain screw located on bottom
center of water tank and drain the water
into empty pail.
■ ■
Empty the tank and then reinstall drain
-screw onto the bottom of tank, turning
until snug. Do NOT over tighten.
■ ■
To place back in working order, fill tank
with water and re-connect the plug.
■ ■
If unit has a filter, the filter must be
removed, turned upside down to drain,
and reinstalled.
Scalding Hazard: The tap dispenses water up
to 98ºC, which can instantly cause scalds or burns.
Use care when operating this appliance.
Property Damage: Join remaining tube
to cold water supply only.
6
Because water supply pipe sizes are
different in each country, up to four water
quick connect fittings are included:
3 /8" to 15mm, 3/8" to 1/2", 3/8" to 1/4" and
3/8" to 1/2" NPT
■ ■
At the other end of the white tube from the
filter, press on one of the above-mentioned
fittings that meet your needs and connect
to the water supply.
■ ■
Press in again to ensure a secure fit.
■ ■
Turn on the cold water supply.
■ ■
Depress the tap’s HOT handle and hold
it until water flows from the spout. Run the
water for at least 2 minutes to flush lines
(both the hot and cold handles on HC1100
independently).
■ ■
Check all connections to ensure they are
tight and that there are no leaks.
■ ■
Plug in tank and ensure that green light
on front of tank is illuminated.
Replace filter cartridge when there is an obvious
decrease in water flow to the tap or if there is an
objectionable taste or odour to the water.
When the inlet and outlet ports have been closed
and the filter’s internal pressure has been relieved,
water (about 60ml) will discharge from vent line.
If the new filter cartridge can not be inserted,
insert the old one and turn until it stops, remove it
and then retry the new cartridge.
It is recommended that carbon filters be replaced
within 6 months.
FILTER GUIDE AND REPLACEMENT
Filter replacement instructions:
■ ■
Replace with an InSinkErator® filter.
■ ■
Place pan or dish towel under the filter to
catch water drainage during change.
■ ■
Slowly turn the cartridge counter-clockwise
completely until it stops (1/4 turn).
■ ■
Pull cartridge straight down and discard.
■ ■
Insert new cartridge into filter head.
■ ■
Top surface of cartridge will become flush
with the bottom of the filter head when
fully engaged.
■ ■
Turn the cartridge clockwise until it stops
(1/4 turn).
■ ■
Align the in/out arrow on the head and
bracket assembly to the in/out arrow on
the cartridge.
■ ■
Open tap to expel trapped air.
■ ■
Run water for 3 minutes before usage.
Factory temperature pre-set is 96˚C.
To reset the thermostat to 96°C, turn
the indicator one notch to the right
of vertical.
After adjusting, depress
the tap handle for 20 seconds for
water to re-heat to the new setting.
■ ■
To adjust water temperature, turn thermostat
dial on the front of the tank clockwise to
increase temperature or turn counter clockwise
to decrease temperature. Repeat if necessary.
All changes should be minimal.
■ ■
Regularly inspect the unit for any signs of
leakage. If there are signs of water damage,
immediately remove the unit from service.
■ ■
To avoid water damage from leakage,
replace all cut, loose or split tubing
.
■ ■
A drain pan, plumbed to an appropriate
drain or outfitted with a leak detector,
should be used in those applications where
any leakage could cause property damage.
PROPERTY DAMAGE
SEASONAL STORAGE/DRAINAGE
CARE AND USE
approx. 96°C
4
Water will be cold at first.
Allow 12-15 minutes for water to
reach target temperature.
Gurgling or hissing is normal
during the initial heating cycle.
Electric Shock Hazard: To prevent electrical shock, disconnect power before
servicing unit. Use only a properly earth (grounded) and polarized electric outlet.
ADJUSTING THE THERMOSTAT
CONNECT WATER & ELECTRICITY
B
A