Illustra IFS03B1BNWIT Скачать руководство пользователя страница 51

Страница: 51 / 139

Illustra Flex Series Installation and Configuration Guide

8200-1456-01 D0

• H264 IntelliZip

• H265

• H265 IntelliZip

• MJPEG

The default setting is ‘H264’.

Select the required

Resolution

from the drop-down menu.

The resolutions available depend on the Image Source selected:

Indoor and Outdoor Dome, Bullet, and Box Camera resolutions

Stream 1

Stream 2

Stream 3

(2048x1536) QXGA 4:3

(1280x720) 720p 16:9

(640x360) nHD 16:9

(1920x1080) 1080p 16:9

(1024x576) PAL+ 16:9

(480x360) 480 4:3

(1664x936) 16:9

(640x360) nHD 16:9

(384x288) 4:3

(1280x720) 720p 16:9

(480x360) 480 4:3

(384x288) 4:3

Use the slider bar to select the

Frame Rate (ips)

The settings for all cameras are:

•

Stream 1 -

1 - 60 ips, default 30. 60FPS is only available on Stream 1

with resolution 1920x1080 or lower.

•

Stream 2 -

1 - 30 ips, default 15 ips. This stream is limited to 15 if

Stream 1 is 60 ips.

•

Stream 3

- 15 ips. This cannot be changed.

Note:

FPS varies depending on other features - refer to the Flex Gen 2 Release Notes for further

information.

If MJPEG has been selected, MJPEG Quality is enabled. Use the slider bar to select the

MJPEG Quality

The default setting is 50.

If H264 has been selected in step 4, Rate Control is enabled. Select the required

Rate

Control

by selecting the radio buttons:

• VBR (Variable Bit Rate)

• CBR (Constant Bit Rate)

• CVBR (Constrained Variable Bit Rate)

The default setting is ‘CVBR’.

If you select VBR, VBR Quality is enabled. Select the required

VBR Quality

from the

drop-down menu. The default setting is High.

•

Highest

Содержание IFS03B1BNWIT












































































































































Результаты поиска

Содержание IFS03B1BNWIT

Отзывы:

Бренды по названию

Популярные бренды

Illustra IFS03B1BNWIT, Руководство по установке и настройке

Результаты поиска

Содержание IFS03B1BNWIT

Отзывы:

Бренды по названию

Популярные бренды