manualshive.com logo in svg

Illustra IFS03B1BNWIT, Руководство по установке и настройке

Поделиться
Скачать
Illustra IFS03B1BNWIT Скачать руководство пользователя страница 120

Illustra Flex Series Installation and Configuration Guide

114

8200-1456-01 D0

- End -

Offline Record Settings

When you configure the Offline Record Settings feature and once it detects a loss of connection with
the recorder, it sends the video stream to the SD card within the unit. This satifies the loss of video
and continues recording. Once the recorder is back online the camera initiates sending recorded
video from the SD card to the recorder. The maximum time recording during the outage depends on
the SD card and the recorded stream you selected. If the SD reaches full capacity, it deletes video
from earliest recording to latest recording. This feature integrates with the VE NVR 5.0 Trickle Stor.

Procedure 149 Configure Offline Recording Settings

Step     Action

1

Select

Setup

on the Web User Interface Banner to display the setup menus.

2

Select

Record Settings

from the

Edge Recording

menu.

3

Select the

Offline Record Settings

tab.

4

In the

Video Edge IP Address

field, enter the IP address of the Video Edge recorder the

camera is connected to.

5

In the

Pre event (secs)

field, enter a time in seconds of the amount of time you want

recorded before the offline event.

6

In the

Post event (secs)

field, enter a time in seconds of the amount of time you wants

recorded after the offline event.

- End -

Event Download

If an event action has record mode enabled, when triggered, the associated video is logged in the
event download table where it can later be downloaded from an SD Card using the specified upload
protocol.

Note:

An event action must have record mode enabled to be logged and downloaded. This is

configured in

Event Actions

under the

Events and Actions

menu.

Содержание IFS03B1BNWIT












































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды