manualshive.com logo in svg

Illustra IFS03B1BNWIT, Руководство по установке и настройке

Поделиться
Скачать
Illustra IFS03B1BNWIT Скачать руководство пользователя страница 118

Illustra Flex Series Installation and Configuration Guide

112

8200-1456-01 D0

you should wait and try again in a few minutes. If this does not work then it may be necessary to
disable Motion Detection, FTP or any other process which may be using the SD Card.

Note:

Refer to the Quick Reference Guide supplied with the product for details on how to remove the

housing assembly and gain access to the camera.

Procedure 144 Insert the SD Card by powering down the Camera

Step     Action

1

Turn off the camera by disconnecting the power supply.

2

Insert the SD card into the camera.

3

Reconnect the power supply and power up the camera.

- End -

Procedure 145 Mount the SD Card through the Web User Interface to
reboot the Camera

Step     Action

1

Insert the MicroSD card into the camera.

2

Select

Setup

on the Web User Interface banner to display the setup menus.

3

Select

SD Card Management

menu from the

Edge Recording

menu.

4

Select

Mount

.

- End -

Removing the MicroSD Card

If at any stage you need to remove the MicroSD card from the camera one of the following two
procedures should be used:

• Remove the SD Card by powering down the camera - Use this procedure if you do not

have access to the Web User Interface and are unable to unmount the MicroSD card
before removal.

• Unmount the SD Card for Removal - Use this procedure when you are unable to

access the power supply to the camera.

Note:

Refer to the Quick Reference Guide supplied with the product for details on how to remove the

housing assembly and gain access to the camera.

Procedure 146 Remove the MicroSD Card by powering down the Camera

1

Turn off the camera by disconnecting the power supply.

2

Remove the SD card from the camera.

Note:

AVI clips are not available on the camera until the MicroSD card has been

inserted and the camera rebooted.

3

Reconnect the power supply and power up the camera.

Содержание IFS03B1BNWIT












































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды