manualshive.com logo in svg

ICT CRX-POSTX-DIN, Руководство по установке, Страница: 44 / 68

Поделиться
Скачать
ICT CRX-POSTX-DIN Скачать руководство пользователя страница 44

44

 

CRX-POSTX-DIN 

DIN Rail PostX IP Reporting Module 

Installation Manual | June 2017 

 

 

13.8

 

Zone Status Indicators 

Whenever a zone input on the PostX Module changes state, the zone status will be displayed on the front panel 
indicator (1-4) corresponding to the physical input number (Z1-Z4). This allows you to easily walk test verification 
of zone inputs. 

 

State 

Description 

1

 

Fast flash 

Zone is in a SHORT state 

1

 

On 

Zone is in a CLOSED state 

1

 

On 

Zone is in an OPEN state 

1

 

Fast flash 

Zone is in a TAMPER state 

 

 

13.9

 

WiFi Indicator 

 

i

 

This information only applies to the PostX modules that support GPRS and/or WIFI communication. 

The WiFi indicator shows the status of the WiFi connection and signal strength. 

 

State 

Description 

 

Wave constantly on 

Connection available 

 

Wave flashing 

Communication / data transfer 

 

WiFi constantly on / 1 bar red 

Connection not established 

 

WiFi constantly on / All bars off 

Connected RSSI level 0 
(lowest signal strength) 

 

WiFi constantly on / 1 bar on 

Connected RSSI level 1 

 

WiFi constantly on / 2 bars on 

Connected RSSI level 2 

 

WiFi constantly on / 3 bars on 

Connected RSSI level 3 

 

WiFi constantly on / 4 bars on 

Connected RSSI level 4   
(highest signal strength) 

 

 

Содержание CRX-POSTX-DIN





































































Отзывы:

Нет отзывов