manualshive.com logo in svg

ICT CRX-POSTX-DIN, Руководство по установке, Страница: 42 / 68

Поделиться
Скачать
ICT CRX-POSTX-DIN Скачать руководство пользователя страница 42

42

 

CRX-POSTX-DIN 

DIN Rail PostX IP Reporting Module 

Installation Manual | June 2017 

 

 

13

 

LED Indicators 

The PostX Module includes comprehensive front panel diagnostic indicators that can aid the installer in 
diagnosing faults and conditions. In some cases an indicator may have multiple meanings depending on the 
status indicator display at the time. 

 

 

13.1

 

Power Indicator 

The Power indicator is lit whenever the correct module input voltage is applied across the N+ and N- terminals. 

 

State 

Description 

 

On (green) 

Correct module input voltage applied   

 

Off 

Incorrect module input voltage applied   

 

 

13.2

 

Status Indicator 

The Status indicator displays module status of the PostX Module. 

 

State 

Description 

    

    

 

Slow (green) flash 

Module operating normally 

 

On (green) 

Module starting up 

 

 

13.3

 

Fault Indicator 

The Fault indicator is lit any time the module is operating in a non-standard mode. 

 

State 

Description 

 

Slow (red) flash 

Module is in boot mode awaiting firmware 
update 

 

 

Содержание CRX-POSTX-DIN





































































Отзывы:

Нет отзывов