IBM s-series Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 170

IBM s-series Скачать руководство пользователя страница 98

Syntax: disable switch-fabric 1 | 2

where

switch-fabric 1

is the left-most module in the B08S and the top-most

module in the B16S, and

switch-fabric 2

is the right-most module in the B08S and

the bottom-most module in the B16S.

To reenable power to the switch fabric module, enter the following command at the
Privileged EXEC level of the CLI:

# enable switch-fabric 1

Syntax: enable switch-fabric 1 | 2

where

switch-fabric 1

is the left-most module in the B08S and the top-most

module in the B16S, and

switch-fabric 2

is the right-most module in the B08S and

the bottom-most module in the B16S.

Displaying management module CPU usage

You can display the amount of the management module’s CPU in use. To do so,
enter the following command at any level of the CLI:

# show cpu
31 percent busy, from 3248 sec ago
1 sec avg: 31 percent busy
5 sec avg: 31 percent busy
60 sec avg: 31 percent busy
300 sec avg: 31 percent busy

Syntax:

show cpu

Removing MAC address entries

You can remove learned MAC address entries from the system’s MAC address
table. You can remove the following:

v

All MAC address entries

v

All MAC address entries for a specified Ethernet port

v

All MAC address entries for a specified VLAN

v

A specified MAC address entry in all VLANs

For example, to remove entries for the MAC address 000d.cb80.00d in all VLANs,
enter the following command at the Privileged EXEC level of the CLI:

# clear mac-address 000d.cb80.00d0

Syntax:

clear mac-address <mac-address> | ethernet <slot>/<port> | vlan

<number>

If you enter the

clear mac-address

command without any parameters, the software

removes all MAC entries.

Use the <mac-address> parameter to remove a specified MAC address from all
VLANs. Specify the MAC address in the following format: HHHH.HHHH.HHHH.

Use the

ethernet

<slot>/<port> parameter to remove all MAC addresses for a

specified Ethernet port. for the <slot> parameter, enter the number of the chassis
slot in which the Ethernet interface module is installed. for the <port> parameter,
enter the Ethernet port whose MAC address you want to remove.

72

Ethernet Switch s-series Installation and User Guide

«
...
96
97
98
99
100
...
»

Содержание s-series











































































































































































Отзывы:

Нет отзывов