IBM s-series Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 170

IBM s-series Скачать руководство пользователя страница 53

Chapter 3. Installing the Chassis

This chapter describes hardware installation tasks for the devices. Before starting
the installation, see; “Safety notices” on page xiii.

CAUTION:
Servicing of this product or unit is to be performed by trained service
personnel only. (C032)

Note:

Information about configuring IP addresses and connecting a chassis to
other network devices are covered in Chapter 4, “Connecting Network
Devices and Checking Connectivity,” on page 45.

Summary of installation tasks

Table 13. Installation tasks for your switch and locations of more detailed information

Task
Number Task

Where to Find More Information

1

Unpack the chassis, and verify that all
contents are present.

“Unpacking a system” on page 28

2

Review the installation cautions and
warnings.

“Installation precautions” on page 28

3

Ensure that the physical environment
that will host the chassis has proper
cabling and ventilation.

“Preparing the installation site” on page
29

4

The B08S ships with extra screws
installed in the right side of the
chassis. These screws secure the fan
tray assembly, protecting it from
damage during shipment. You must
remove these screws before installing
the chassis.

“Removing extra shipment screws (B08S
only)” on page 29

5

Install the chassis in a rack.

Because of the weight of a fully
loaded chassis (97 lbs minimum), IBM
recommends mounting a chassis in a
rack before installing the modules and
power supplies.

“Installing a chassis in a rack” on page 30

6

The chassis ships with a slot panel
installed in all module slots that don’t
currently have a module installed. If
you plan to install a module in a slot,
you must remove the slot panel.

If you do not install a module in a slot,
you must keep the slot panel in place.
If you run the chassis with an
uncovered slot, the system will
overheat.

“Removing the slot panels” on page 32

7

Install the management module and
interface modules in the chassis

“Installing the management and interface
modules” on page 33

© Copyright IBM Corp. 2009

27

«
...
51
52
53
54
55
...
»

Содержание s-series











































































































































































Отзывы:

Нет отзывов