IBM s-series Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 170

IBM s-series Скачать руководство пользователя страница 85

Table 18. Chassis status and temperature Information

This Field...

Displays...

Chassis Type

This field displays the chassis type. for example:

v

B08S

v

B16S

v

-PREM indicates that the device is a premium device (supports full Layer 2
switching and full Layer 3 multiprotocol routing).

Power

Power Supply

Indicates whether a power supply is installed in the specified power supply slot and
the status of the power supply, which can be one of the following:

OK - The power supply is functioning properly and supplying power to the chassis
and installed modules.

Failed - The power supply is not functioning and is not supplying power to the
chassis and installed modules.

This field also indicates:

v

the manufacturing part number

v

whether the supply is AC

v

whether the supply is regular or POE

On the B08S, Power Supply 1 is the left-most slot, and Power Supply 4 is the
right-most slot. These numbers assume you are facing the front of the chassis, not
the rear.

On the B16S, Power Supply 1 is the top left-most slot, Power Supply 4 is the top
right-most slot, Power Supply 5 is the bottom left-most slot, and Power Supply 8 is
the right-most slot. These numbers assume you are facing the front of the chassis,
not the rear.

Fans

Fan <number>

For the B08S, this field displays information about fans 1 through 6. Fan locations
are as follows:

v

Fan 1 - Left-most fan in bottom row

v

Fan 2 - Middle fan in bottom row

v

Fan 3 - Right-most fan in bottom row

v

Fan 4 - Left-most fan in top row

v

Fan 5 - Middle fan in top row

v

Fan 6 - Right-most fan in top row

For the B16S, this field displays information about fans 1 and 2. Fan locations are
as follows:

v

Fan 1 - This is Fan A and is the right-most fan in the rear of the chassis.

v

Fan 2 - This is Fan B and is the left-most fan in the rear of the chassis.

<Fan status>

The status of a fan can be one of the following:

OK - The fan is functioning properly and is keeping the temperature of each module
within an acceptable temperature range.

Failed - The fan is not functioning properly or the fan control module cannot control
the fan.

Chapter 5. Managing the Chassis and Modules

59

«
...
83
84
85
86
87
...
»

Содержание s-series











































































































































































Отзывы:

Нет отзывов