IBM s-series Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 170

IBM s-series Скачать руководство пользователя страница 74

Global CONFIG Level:

FastIron(config)#

4. Configure the IPv4 address and mask for the switch.

FastIron(config)# ip address 192.22.3.44 255.255.255.0

5. Set a default gateway address for the switch.

FastIron(config)# ip default-gateway 192.22.3.1

Note:

You do not need to assign a default gateway address for single subnet
networks.

Syntax: enable [<password>]

Syntax: configure terminal

Syntax: [no] ip address <ip-addr> <ip-mask>

or

Syntax: [no] ip address <ip-addr>/<mask-bits>

Syntax: ip default-gateway <ip-addr>

IPv6 devices

IPv6 devices support the 128-bit addressing format, composed of 8 fields of 16-bit
hexadecimal values separated by colons (:). For example,

2001:0000:0000:0200:002D:D0FF:FE48:4672

is an IPv6 address, which can also be

expressed as

2001:0:0:200:2D:D0FF:FE48:4672

after omitting the leading zeros.

IPv6 devices running Layer 3 software

Before attaching equipment to a router, you must assign an interface IP address to
the subnet on which the router will be located. You must use the serial connection
to assign the first IP address. for subsequent addresses, you also can use the CLI
through Telnet or the Web management interface.

By default, you can configure up to 24 IP interfaces on each port, virtual interface,
and loopback interface. You can increase this amount to up to 64 IP subnet
addresses per port by increasing the size of the subnet-per-interface table. See the

Configuration Guide

For more information.

The following procedure shows how to add an IPv6 address and mask to a router
port.

1. At the opening CLI prompt, enter

enable

.

FastIron> enable

2. Enter the following command at the CLI Privileged EXEC level prompt, then

press

Enter

. This command erases the factory test configuration if still present:

FastIron# erase startup-config

Attention:

Use the

erase startup-config

command only for new systems. If

you enter this command on a system you have already configured, the
command erases the configuration. If you accidentally do erase the
configuration on a configured system, enter the

write memory

command to

save the running configuration to the startup-config file.

3. Access the configuration level of the CLI by entering the following command:

Privileged EXEC Level:

FastIron# configure terminal

Global CONFIG Level:

48

Ethernet Switch s-series Installation and User Guide

«
...
72
73
74
75
76
...
»

Содержание s-series











































































































































































Отзывы:

Нет отзывов