IBM s-series Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 170

IBM s-series Скачать руководство пользователя страница 76

EUI-64 interface ID as the system-wide address for the switch. A link-local
IPv6 address is also supported. For details, see the

Configuration Guide

.

Syntax: enable [<password>]

Syntax: configure terminal

Syntax: [no] ipv6 address <ipv6-prefix>/<prefix-length>

You must specify the <ipv6-prefix> parameter in hexadecimal using 16-bit values
between colons as documented in RFC 2373.

You must specify the <prefix-length> parameter in decimal value. A slash mark (/)
must follow the <ipv6-prefix> parameter and precede the <prefix-length>
parameter.192.22.3.44 255.255.255.0

Connecting network devices

These devices support connections to other vendors’ routers, switches, and hubs,
as well other IBM devices.

Cable specifications

See “Cable specifications” on page 127 for cable lengths and types.

Connecting to Ethernet or fast Ethernet hubs

For copper connections to Ethernet hubs, a 10/100Base-TX or 1000Base-T switch,
or another IBM device, a crossover cable is required. If the hub is equipped with an
uplink port, it will require a straight-through cable instead of a crossover cable.

Note:

The 802.3ab standard (automatic MDI/MDIX detection) calls for automatic
negotiation of the connection between two 1000Base-T ports. Therefore, a
crossover cable may not be required; a straight-through cable may work as
well. For more information about this feature, see the

Configuration Guide

.

Figure 26 on page 51 shows a UTP crossover cable.

50

Ethernet Switch s-series Installation and User Guide

«
...
74
75
76
77
78
...
»

Содержание s-series











































































































































































Отзывы:

Нет отзывов