IBM s-series Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 170

IBM s-series Скачать руководство пользователя страница 18

DANGER

Overloading a branch circuit is potentially a fire hazard and a
shock hazard under certain conditions. To avoid these hazards,
ensure that your system electrical requirements do not exceed
branch circuit protection requirements. Refer to the information
that is provided with your device or the power rating label for
electrical specifications. (D002)

DANGER

If the receptacle has a metal shell, do not touch the shell until
you have completed the voltage and grounding checks. Improper
wiring or grounding could place dangerous voltage on the metal
shell. If any of the conditions are not as described, STOP. Ensure
the improper voltage or impedance conditions are corrected
before proceeding. (D003)

DANGER

An electrical outlet that is not correctly wired could place
hazardous voltage on metal parts of the system or the devices
that attach to the system. It is the responsibility of the customer
to ensure that the outlet is correctly wired and grounded to
prevent an electrical shock. (D004)

The following general electrical danger notice provides instructions on how to avoid
shock hazards when servicing equipment. Unless instructed otherwise, follow the
procedures in this danger notice.

xvi

Ethernet Switch s-series Installation and User Guide

«
...
16
17
18
19
20
...
»

Содержание s-series











































































































































































Отзывы:

Нет отзывов