IBM s-series Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 170

IBM s-series Скачать руководство пользователя страница 75

FastIron(config)#

4. Configure the IPv6 address and mask address for the interface:

FastIron(config)# int e 1/5
FastIron(config-if-e1000-1/5)# ipv6 address
2001:200:12D:1300:240:D0FF:FE48:4672:/64

These commands configure the global prefix 2001:200:12d:1300::/64 and the
interface ID ::240:D0FF:FE48:4672, and enable IPv6 on interface e 1/5.

Note:

The above procedure shows how to configure an IPv6 address with a
manually configured Interface ID as the address for the interface. You could
also configure an IPv6 address with an automatically computed EUI-64
Interface ID as the address for the interface. Link-local IPv6 addresses are
also supported. For details, see the

Configuration Guide

.

Syntax: enable [<password>]

Syntax: configure terminal

Syntax: [no] ipv6 address <ipv6-prefix>/<prefix-length>

You must specify the <ipv6-prefix> parameter in hexadecimal using 16-bit values
between colons as documented in RFC 2373.

You must specify the <prefix-length> parameter in decimal value. A slash mark (/)
must follow the <ipv6-prefix> parameter and precede the <prefix-length> parameter.

IPv6 devices running Layer 2 software

To configure an IPv6 address to a device running Layer 2 software:

1. At the opening CLI prompt, enter

enable

.

FastIron> enable

2. Enter the following command at the Privileged EXEC level prompt (for example,

#

), then press

Enter

. This command erases the factory test configuration if still

present:

FastIron# erase startup-config

Attention:

Use the

erase startup-config

command only for new systems. If

you enter this command on a system you have already configured, the
command erases the configuration. If you accidentally do erase the
configuration on a configured system, enter the

write memory

command to

save the running configuration to the startup-config file.

3. Access the configuration level of the CLI by entering the following command:

Privileged EXEC Level:

FastIron# configure terminal

Global CONFIG Level:

FastIron(config)#

4. Configure the IP address and mask for the switch.

FastIron(config)# ipv6 address 2001:200:12D:1300:240:D0FF:FE48:4000:1/64

Note:

The above procedure shows how to configure an IPv6 address with a
manually configured interface ID as the system-wide address for the switch.
You could also configure an IPv6 address with an automatically computed

Chapter 4. Connecting Network Devices and Checking Connectivity

49

«
...
73
74
75
76
77
...
»

Содержание s-series











































































































































































Отзывы:

Нет отзывов