IBM IntelliStation E Pro Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 182

background image

Internal drive bays

The IntelliStation E Pro Type 6226 computer comes with a 3.5-in. 1.44-MB diskette
drive in bay 1; a hard disk drive installed in bay 2; and an IDE CD-ROM,
DVD-ROM, or CD-RW drive in bay 3.

Bay 1

Bay 2

Bay 4

Bay 3

Notes:

1. The IntelliStation E Pro Type 6226 computer supports only one diskette drive.

2. For a complete list of supported options for the computer, go to

http://www.ibm.com/pc/support/ on the World Wide Web.

Preinstallation steps

Before you replace drives in the computer, verify that you have all the cables and
other equipment specified in the documentation that comes with the drive. You
might also need to perform certain preinstallation activities. Some steps are
required only during the initial installation of an option.

1. Read “Safety information” on page 129, “Handling electrostatic

discharge-sensitive devices” on page 132, and the documentation that comes
with the drive.

2. Choose the bay in which you want to install the drive.

3. Check the instructions that come with the drive to see if you need to set any

switches or jumpers on the drive. If you are installing a SCSI device, be sure to
set the SCSI ID for that device.

Power and signal cables for internal drives

The computer uses cables to connect IDE, SCSI, and diskette devices to the power
supply and to the system board. The following cables are provided:

v

Four-wire power cables connect the drives to the power supply. At the end of
these cables are plastic connectors that attach to different drives; these
connectors vary in size. Also, certain power cables attach to the system board.

v

Flat signal cables, also called ribbon cables, connect IDE and diskette drives to
the system board. There are two sizes of ribbon cables that come with the
computer.

– The wider IDE signal cable has two or three connectors.

- If the cable has three connectors, one of these connectors is attached to

the drive, one is a spare, and the third attaches to the primary or secondary
IDE connector on the system board.

64

IBM IntelliStation E Pro Types 6216 and 6226: Hardware Maintenance Manual

«
...
72
73
74
75
76
...
»

Содержание IntelliStation E Pro























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IntelliStation E Pro

Бренд: Acer Страницы: 30

Бренд: Gateway Страницы: 12

PT-970 A Series

Бренд: Contec Страницы: 77

Бренд: ECS Страницы: 53

Бренд: Gateway Страницы: 144

FlowControl FC-S01

Бренд: Go!Paint Страницы: 20

Бренд: MiTAC Страницы: 246

Бренд: MSI Страницы: 1

Бренд: MSI Страницы: 41

Бренд: LG Страницы: 24

Бренд: LG Страницы: 41

Бренд: LG Страницы: 136

Бренд: IBM Страницы: 72

Бренд: Gateway Страницы: 2

Бренд: Gateway Страницы: 98

Бренд: Gateway Страницы: 190

Бренд: HONEYWELL BULL Страницы: 73

Tank GT20 (B5211)

Бренд: TYAN Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды