IBM IntelliStation E Pro Скачать руководство пользователя

Страница: 72 / 182

9. Carefully grasp the adapter by the top edge or upper corners, and align it with

the expansion slot guides; then, press the adapter

firmly

into the expansion

slot.

Expansion-slot cover

Adapter-support bracket

Attention:

Be certain that the adapter is correctly seated in the expansion slot

before you turn on the computer. Incomplete installation of an adapter might
damage the system board or the adapter.

10. Connect required cables to the adapter.

11. If you have another adapter to install, repeat steps 1 through 12 on page 47. If

you have another option to install, do so now. Otherwise, complete the
remaining steps in this section.

12. Reinstall the rear-adapter-support bracket; then, rotate the bracket to the

closed (locked) position.

13. Return the drive bay cages to their original positions in the computer.

14. Replace the top cover (see “Replacing the cover of the 6226” on page 72).

15. Reconnect the external cables and power cords; then, turn on the attached

devices and the computer.

Installing a SCSI adapter

Complete the following steps to install an optional SCSI adapter:

1. Complete steps 1 through 12 of “Installing an adapter” on page 61; then,

continue with step 2.

2. Connect the SCSI signal cable to the adapter and one or more of the signal

cable connectors to the rear of the SCSI devices.

3. Connect the SCSI activity indicator cable to the adapter and to the SCSI LED

connector (CN23) on the system board (see “System board” on page 58 for the

IBM IntelliStation E Pro Types 6216 and 6226: Hardware Maintenance Manual

Содержание IntelliStation E Pro























































































































































































Результаты поиска

Содержание IntelliStation E Pro

Отзывы:

Похожие инструкции для IntelliStation E Pro

Бренды по названию

Популярные бренды

IBM IntelliStation E Pro, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание IntelliStation E Pro

Отзывы:

Похожие инструкции для IntelliStation E Pro

Бренды по названию

Популярные бренды