IBM IntelliStation E Pro Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 182

background image

3. Rotate the CD-ROM drive cage up.

4. Disconnect any cables that impede access to the microprocessor.

5. Remove the fan-sink assembly from the microprocessor:

Note:

The fan and underlying heat sink are attached and do not need to be
separated from each other. Remove the fan-sink assembly from the
microprocessor as a single unit.

a. Detach the fan-sink cable.

b. Loosen the two captive screws (in leaf-spring enclosures) on either side of

the fan-sink assembly.

c. With the two captive screws loosened, pivot the leaf spring assemblies

outward and out of the notches on the fan-sink assembly.

d. Lift the fan-sink assembly up and out of the computer.

Note:

It might be necessary to gently twist the fan-sink assembly to loosen
it from the microprocessor.

Important:

Be careful when handling the adhesive material on the
microprocessor. If the adhesive material on the microprocessor
will be reused, do not contaminate it. If replacement adhesive
material is provided with the replacement part, be sure to
remove all traces of existing adhesive material from the
microprocessor before applying the new adhesive material.

6. Free the microprocessor from the system board by rotating the microprocessor

socket lever arm upward to its maximum vertical position.

7. Lift the microprocessor up and out of the computer.

To install a microprocessor, reverse the previous steps.

92

IBM IntelliStation E Pro Types 6216 and 6226: Hardware Maintenance Manual

«
...
100
101
102
103
104
...
»

Содержание IntelliStation E Pro























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IntelliStation E Pro

Бренд: Raven Страницы: 71

Бренд: Igel Страницы: 2

Бренд: Igel Страницы: 2

Бренд: iDOT Страницы: 66

Бренд: DFI Страницы: 69

Бренд: Avalue Technology Страницы: 78

FieldGo PCATX-R9

Бренд: BSi Страницы: 40

Бренд: Intel Страницы: 2

Бренд: Dell Страницы: 54

Бренд: Acer Страницы: 74

Бренд: Acer Страницы: 83

Бренд: Acer Страницы: 77

Бренд: Acer Страницы: 97

Бренд: Acer Страницы: 73

Бренд: Acer Страницы: 28

Бренд: Acer Страницы: 105

Бренд: Acer Страницы: 98

Бренд: Acer Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды