Huawei SmartLi 2.0 Скачать руководство пользователя страница 81

Страница: 81 / 173

Figure 4-37 Installing battery communications cables

(1) Full-capacity cabinet (7+7 scenario)

(2) Half-capacity cabinet (7+0 scenario)

Step 5 Install battery copper bars and power cables.

1. Open the terminal protective covers, install copper bars between battery

modules, and close the terminal protective covers.

2. Open the terminal protective covers, install copper bars between battery

modules and fuses, and close the terminal protective covers.

3. Open the terminal protective covers, install the battery power cables reserved

in the cabinet, and close the terminal protective covers.

NO TICE

● When installing a copper bar, connect the part with a round hole to the upper

battery module, and connect the part with a slotted hole to the lower battery

module. Install the part with a round hole first, and then the part with a slotted

hole.

● Excessive bolts will be used as spare parts.

WARNING

After removing the safety cap from the power cable of the battery at the bottom

layer, install the cable immediately to prevent the exposed terminal from touching

the shell, which may cause sparks or burns.

SmartLi 2.0

User Manual

4 Installation

Issue 09 (2022-01-30)

Содержание SmartLi 2.0














































































































































































Результаты поиска

Содержание SmartLi 2.0

Отзывы:

Huawei SmartLi 2.0, Руководство пользователя, Страница: 81 / 173

Результаты поиска

Содержание SmartLi 2.0

Отзывы: