manualshive.com logo in svg

Huawei SmartLi 2.0, Руководство пользователя, Страница: 15 / 173

Поделиться
Скачать
Huawei SmartLi 2.0 Скачать руководство пользователя страница 15

General Requirements

Use dedicated insulated tools when performing high-voltage operations.

DC Operation Requirements

D ANGER

Do not install or remove power cables with power on. Transient contact between

the core of the power cable and the conductor will generate electric arcs or

sparks, which may cause fire or personal injury.

●

Before installing or removing power cables, ensure that the switch is turned

off.

●

Before connecting a power cable, check that the label on the power cable is

correct.

●

A damaged cable must be replaced by the manufacturer, service agent, or

professionals to avoid risks.

●

Only qualified personnel are allowed to perform high-voltage operations on

the equipment.

Cabling

●

When routing cables, ensure that a distance of at least 30 mm exists between

the cables and heat-generating components or areas. This prevents damage

to the insulation layer of the cables.

●

Do not route cables behind the air intake and exhaust vents of the

equipment.

●

Ensure that cables meet the VW-1 or ZB and higher flame spread rating

requirements.

●

Bind cables of the same type together. When routing cables of different types,

ensure that they are at least 30 mm away from each other.

●

If a cable is connected to the cabinet from the top, bend the cable in a U

shape outside the cabinet and then route it into the cabinet.

●

When the temperature is low, violent impact or vibration may damage the

plastic cable sheathing. To ensure safety, comply with the following

requirements:
–

Cables can be laid or installed only when the temperature is higher than

0°C. Handle cables with caution, especially at a low temperature.

–

Cables stored at subzero temperatures must be stored at room

temperature for at least 24 hours before they are laid out.

●

Do not perform any improper operations, for example, dropping cables

directly from a vehicle.

●

When selecting, connecting, and routing cables, follow local safety regulations

and rules.

SmartLi 2.0

User Manual

1 Safety Information

Issue 09 (2022-01-30)

Copyright © Huawei Technologies Co., Ltd.

5

Содержание SmartLi 2.0














































































































































































Отзывы:

Нет отзывов