Huawei SmartLi 2.0 Скачать руководство пользователя страница 139

Страница: 139 / 173

Routine Maintenance

●

Before performing operations, read through the user manual and pay

attention to safety precautions and battery connection methods.

●

Before maintenance, get the tools insulated.

●

Keep the battery switch off during installation and maintenance.

●

Before installing and maintaining the battery modules, remove the BCU, and

reinstall the BCU after the installation or maintenance is complete.

●

When moving batteries, handle batteries gently, and pay attention to personal

safety.

●

Never use any organic solvent to clean batteries.

●

Do not use wet cloth to clean exposed copper bars or other conductive parts.

●

Never smoke or have an open flame around batteries.

●

After battery discharge, charge the battery in time to maintain a good service

life.

●

Only professionals are allowed to perform the maintenance tasks.

SmartLi 2.0

User Manual

7 Routine Maintenance

Issue 09 (2022-01-30)

129

Содержание SmartLi 2.0














































































































































































Результаты поиска

Содержание SmartLi 2.0

Отзывы:

Huawei SmartLi 2.0, Руководство пользователя, Страница: 139 / 173

Результаты поиска

Содержание SmartLi 2.0

Отзывы: