Huawei SmartLi 2.0 Скачать руководство пользователя страница 156

Страница: 156 / 173

NO TICE

The fire-trace tube may contain high-pressure extinguishant. Loosen the

connection nut slowly; otherwise, extinguishant may be released

unexpectedly.

3. Remove the fire-trace tube.
4. Remove the fire extinguisher cylinder fastener.
5. Take out the fire extinguisher cylinder.

Figure 9-11 Removing the fire extinguisher cylinder

NO TE

The methods for removing the fire extinguisher cylinder from the front and rear of the

SmartLi cabinet are the same. This figure shows how to remove the fire extinguisher

cylinder from the front of the SmartLi cabinet.

Step 9 Install a new fire extinguisher cylinder. Keep it upright.

Step 10 Install the fire-trace tube on the fire extinguisher cylinder.

NO TICE

Do not bend or twist the fire-trace tube or bind the tube using cable ties.

Otherwise, the fire extinguisher cylinder may fail.

1. Cut off the end of the fire-trace tube evenly.

SmartLi 2.0

User Manual

9 Parts Replacement

Issue 09 (2022-01-30)

146

Содержание SmartLi 2.0














































































































































































Результаты поиска

Содержание SmartLi 2.0

Отзывы:

Huawei SmartLi 2.0, Руководство пользователя, Страница: 156 / 173

Результаты поиска

Содержание SmartLi 2.0

Отзывы: