Huawei SmartLi 2.0 Скачать руководство пользователя страница 7

Страница: 7 / 173

WARNING

Do not transport a cabinet with battery modules installed. If the cabinet needs to

be transported or moved, remove the battery modules first.

CA UTION

Strictly follow the instructions in this document during storage, transportation,

installation, and maintenance to prevent risks caused by system exceptions.

CA UTION

If the battery cabinet is installed but not powered on, manually powered off, or

discharged, avoid keeping it at low SOC for an extended period. Recharge the

battery cabinet in a timely manner according to the instructions in Transportation

and Storage > Battery Cabinet Storage with Low SOC in the user manual.

Otherwise, batteries may be damaged due to overdischarge.

CA UTION

After the lithium battery system is installed, fully charge the system before putting

it into use. When the system is in operation, do not replace battery modules

without permission.

CA UTION

Battery modules should not be stored for an extended period. They should be used

soon after being deployed onsite. For battery modules that have been stored for

an extended period, recharge them periodically according to the instructions in

Transportation and Storage > Battery Module Storage and Recharge in the

user manual. Otherwise, the battery modules may be damaged.

SmartLi 2.0

User Manual

Important Safety Instructions

Issue 09 (2022-01-30)

Содержание SmartLi 2.0














































































































































































Результаты поиска

Содержание SmartLi 2.0

Отзывы:

Huawei SmartLi 2.0, Руководство пользователя, Страница: 7 / 173

Результаты поиска

Содержание SmartLi 2.0

Отзывы: