HP P2000 G3 Скачать руководство пользователя

Страница: 333 / 532

HP P2000 G3 MSA System CLI Reference Guide 333

CAUTION:

It is recommended to avoid reconstruction after using the

trust

command.

Reconstruction causes heavy usage of disks that were already reporting errors. This usage could

cause the disks to fail during reconstruction, which can cause data to be unrecoverable.

Enable the

trust

command.

Run the

trust

command on the vdisk.

If the

trust

command determines that it would be unsafe to proceed, it will fail. If this happens

you can either:
• Please contact Support for further assistance. This is recommended.
• Proceed by re-enabling

trust

and running

trust

with the

unsafe

parameter. This is not

recommended because in most cases it will result in an unstable vdisk with data corruption.

After running the trust command

Reinsert the host-port cables.

Perform a complete backup of the vdisk.

Delete the vdisk.

Replace the failed disks with new disks.

Re-create the vdisk.

Restore the data from the backup performed in step 2.

Restore original vdisk ownership.

Re-enable background scrub operations.

Syntax

trust

[enable|disable]

[vdisk

vdisk

]

[unsafe]

Parameters

enable|disable

Optional.

•

enable

: Enables the

trust

command before use.

•

disable

: Disables the

trust

command if it is not used after being enabled. If

trust

is not

explicitly disabled, it will be automatically disabled when the user’s CLI session ends.

vdisk

vdisk

Optional. The name or serial number of the vdisk to trust. For vdisk syntax, see

Command syntax

page 22.

unsafe

Optional. Specifies to proceed with a trust operation that is determined to be unsafe because it must

use out-of-sync or partially reconstructed disks, which in most cases will result in an unstable vdisk

with data corruption.

Output With the

unsafe

parameter

Location

The enclosure ID and slot number of the disk.

Serial Number

The serial number of the disk.

Type

•

SAS: Dual-port SAS

•

SAS-S: Single-port SAS

•

SATA: Dual-port SATA

•

SATA-S: Single-port SATA

Содержание P2000 G3





















































































































































































































































































































































































































































































































































Результаты поиска

Содержание P2000 G3

Отзывы:

Похожие инструкции для P2000 G3

Бренды по названию

Популярные бренды

HP P2000 G3, Справочное руководство CLI

Результаты поиска

Содержание P2000 G3

Отзывы:

Похожие инструкции для P2000 G3

Бренды по названию

Популярные бренды