HP P2000 G3 Скачать руководство пользователя

Страница: 163 / 532

HP P2000 G3 MSA System CLI Reference Guide 163

controller a|b

Optional. For IP-related parameters, this specifies whether to apply settings to controller A or B. If this

parameter is omitted, settings are applied to the controller being accessed. This parameter does not

apply to Ethernet switch-related parameters, whose settings are always applied to the controller

being accessed.

ping-broadcast enabled|disabled|on|off

Optional. Enables the storage system to respond when a ping to a broadcast address is issued on

the system’s subnet.

link-speed 10mbps|100mbps

Optional. Specifies the maximum link speed for auto-negotiation.

•

10mbps

: Sets the link speed to 10 Mb/s.

•

100mbps

: Sets the link speed to 100 Mb/s. If this parameter is omitted and a port’s link speed

is not set, it will be set to 100 Mb/s.

duplex-mode full|half

Optional. Specifies the duplex mode.

•

full

: Sets the port to use full duplex. If this parameter is omitted and a port’s duplex mode is not

set, it will be set to full duplex.

•

half

: Sets the port to use half duplex.

auto-negotiation enabled|disabled|on|off

Optional. Specifies whether to auto-negotiate the link speed.

•

enabled

: Enables auto-negotiation. If you enable auto-negotiation you must also specify

the

link-speed

parameter to set the maximum supported speed for auto-negotiation. Because

the controller will choose the proper duplex mode for the negotiated speed, you cannot specify

the

duplex-mode

parameter.

•

disabled

off

: Disables auto-negotiation. If you disable auto-negotiation and don’t specify

the

link-speed

and

duplex-mode

parameters, the controller will use the current settings of

the network port.

If this command is specified and the

auto-negotiation

parameter is omitted, auto-negotiation

will be enabled.

prompt yes|no

Optional. For scripting, this specifies an automatic response to the confirmation prompt that appears

when an Ethernet switch parameter is changed:

•

yes

: Allow the command to proceed.

•

: Cancel the command.

If this parameter is omitted, you must manually reply to the prompt.

noprompt

Optional in console format; required for XML API format. Suppresses the confirmation prompt that

appears when an Ethernet switch parameter is changed, which requires a yes or no response.

Specifying this parameter allows the command to proceed without user interaction.

Example

Use DHCP to set network port IP values:

# set network-parameters dhcp

Success: Command completed successfully. - Request to set network parameters has
been initiated. (2011-10-12 12:26:45)

Manually set network port IP values for controller A (disabling DHCP for both controllers, if it was

enabled):

# set network-parameters ip 192.168.0.10 netmask 255.255.255.0 gateway
192.168.0.1 controller a

Success: Command completed successfully. - Request to set network parameters has
been initiated. (2012-01-21 12:26:50)

Содержание P2000 G3





















































































































































































































































































































































































































































































































































Результаты поиска

Содержание P2000 G3

Отзывы:

Похожие инструкции для P2000 G3

Бренды по названию

Популярные бренды

HP P2000 G3, Справочное руководство CLI

Результаты поиска

Содержание P2000 G3

Отзывы:

Похожие инструкции для P2000 G3

Бренды по названию

Популярные бренды