162 Alphabetical list of commands
set network-parameters
Description
Sets parameters for controller module network ports.
You can manually set static IP values for each controller, or you can specify that IP values should be
set automatically for both controllers through communication with a Dynamic Host Configuration
Protocol (DHCP) server.
Each controller has the following factory-default IP settings:
•
DHCP: enabled
•
Controller A IP address: 10.0.0.2
•
Controller B IP address: 10.0.0.3
•
IP subnet mask: 255.255.255.0
•
Gateway IP address: 10.0.0.1
When DHCP is enabled, the following initial values are set and remain set until the system is able to
contact a DHCP server for new addresses.
•
Controller A IP address: 10.0.0.2
•
Controller B IP address: 10.0.0.3
•
IP subnet mask: 255.255.255.0
•
Gateway IP address: 0.0.0.0
To switch a controller from DHCP addressing to static addressing, you must set the IP address,
netmask, and gateway values.
You can also set link speed, auto-negotiation, and duplex-mode parameters to enable Ethernet
switches to communicate with the storage system. These settings will persist if the Ethernet cable is
disconnected and reconnected, but will revert to default values if the controller is removed from the
enclosure. These settings affect only the network port of the controller on which this command is
entered.
Syntax
set network-parameters
[dhcp]
[ip
address
]
[netmask
netmask
]
[gateway
gateway
]
[controller a|b]
[ping-broadcast enabled|disabled|on|off]
[link-speed 10mbps|100mbps]
[duplex-mode full|half]
[auto-negotiation enabled|disabled|on|off]
[prompt yes|no]
[noprompt]
Parameters
dhcp
Optional. Specifies to use DHCP to set both controllers’ IP values.
ip
address
Optional. An IP address for the port.
netmask
netmask
Optional. An IP subnet mask for the port.
gateway
gateway
Optional. A gateway IP address for the port.
Содержание P2000 G3
