HP P2000 G3 Скачать руководство пользователя страница 158

Страница: 158 / 532

158 Alphabetical list of commands

set iscsi-parameters

Description

For iSCSI, changes system-wide iSCSI parameters.

Syntax

set iscsi-parameters

[chap enabled|disabled|on|off]

[jumbo-frame enabled|disabled|on|off]

[speed auto|1gbps]

[isns enabled|disabled|on|off]

[isns-ip

iSNS-IP

]

[isns-alt-ip

iSNS-IP

]

[iscsi-ip-version ipv4|ipv6]

Parameters

chap enabled|disabled|on|off

Enables or disables use of Challenge Handshake Authentication Protocol. Disabled by default.

jumbo-frame enabled|disabled|on|off

Enables or disables support for jumbo frames. Disabled by default. A normal frame can contain

1500 bytes whereas a jumbo frame can contain a maximum of 9000 bytes for larger data transfers.

Use of jumbo frames can succeed only if jumbo-frame support is enabled on all network components

in the data path.

speed auto|1gbps

Sets the host port link speed.

•

auto

: Auto-negotiates the proper speed. This is the default.

•

1gbs

: Forces the speed to 1 Gbit/sec, overriding a downshift that can occur during

auto-negotiation with 1-Gbit/sec HBAs. This setting does not apply to 10-Gbit/sec HBAs.

isns enabled|disabled|on|off

Enables or disables registration with a specified Internet Storage Name Service server, which

provides name-to-IP-address mapping. Disabled by default.

isns-ip

iSNS-IP

Specifies the IP address of an iSNS server. The default address is all zeroes.

isns-alt-ip

iSNS-IP

Optional. Specifies the IP address of an alternate iSNS server, which can be on a different subnet.

The default address is all zeroes.

iscsi-ip-version ipv4|ipv6

Optional. Specifies whether to use IP version 4 (IPv4) or 6 (IPv6) for addressing controller iSCSI

ports.

•

ipv4

: Lets you specify addresses in dot-decimal format, where the four octets of the address use

decimal values without leading zeroes and the octets are separated by a period; for example,

10.132.2.205

. This option is the default.

•

ipv6

: Lets you specify addresses using eight groups of four hexadecimal digits, where the

groups are separated by a colon. All groups must be specified. For example,

0000:0000:0000:0000:0000:0000:0A90:3442.

Example

For a storage system whose host ports are connected to different subnets, enable CHAP, specify the

IP address of the iSNS server on each subnet, and enable registration with either server:

# set iscsi-parameters chap enabled isns enabled isns-ip 10.10.10.93 isns-alt-ip
10.11.10.90

Success: Command completed successfully. - iSCSI parameter(s) were changed
successfully. (2012-01-21 12:21:15)

Specify that iSCSI ports will use IPv6 addressing:

# set iscsi-parameters iscsi-ip-version ipv6

Success: Command completed successfully. - iSCSI parameter(s) were changed
successfully. (2012-01-21 12:21:20)

Содержание P2000 G3





















































































































































































































































































































































































































































































































































Результаты поиска

Содержание P2000 G3

Отзывы:

Бренды по названию

Популярные бренды

HP P2000 G3, Справочное руководство CLI

Результаты поиска

Содержание P2000 G3

Отзывы:

Бренды по названию

Популярные бренды