manualshive.com logo in svg

HP 5800, Справочник по командам

Поделиться
Скачать
HP 5800 Скачать руководство пользователя страница 78

 

69 

 Session State   : Operational          Session Role   : Active 

 Session FT Flag : Off                  MD5 Flag       : Off 

 Reconnect Timer : ---                  Recovery Timer : --- 

                                                                      

 Negotiated Keepalive Timer        : 45 Sec 

 Keepalive Message Sent/Rcvd       : 25/25 (Message Count) 

 Label Advertisement Mode          : Downstream Unsolicited 

 Label Resource Status(Peer/Local) : Available/Available 

 Peer Discovery Mechanism          : Basic 

 Session existed time              : 000:00:06  (DDD:HH:MM) 

 LDP Basic Discovery Source        : Vlan-interface1 

 Label Acceptance Policy           : prefix-from-rt1 

                                                                       

 Addresses received from peer: (Count: 3) 

 10.1.1.2            20.1.1.1            2.2.2.2                       

                                                                     

-------------------------------------------------------------------------- 

Table 30

 

Command output 

Field Description 

Peer LDP ID 

LDP identifier of the peer. See 

Table 24

 for detailed 

description of LDP ID. 

Local LDP ID 

Local LDP identifier. See 

Table 24

 for detailed 

description of LDP ID. 

Session State 

See 

Table 29

 to view the session states. 

Session Role 

Role of the current LSR in the session, Active or 
Passive. 

Session FT Flag 

Whether GR FT is enabled on the peer of the 
session. 

MD5 Flag 

Whether MD5 authentication is enabled on the 
peer. 

Label Resource Status(Peer/Local) 

Whether free labels exist on the local and remote 
peers. 

Peer Discovery Mechanism 

Discovery mechanism of the peer: Basic or 
Extended. 

Session existed time 

Length of time that elapsed since the session is 
established. 

LDP Basic Discovery Source 

LDP Extended Discovery Source 

Interface where the session is established. The value 
is the name of the interface for basic discovery and 

name of the remote peer for extended discovery. 

Reconnect Timer 

GR reconnect timer. 

Recovery Timer 

GR recovery timer. 

Label Acceptance Policy 

Label acceptance control policy. 

 

Содержание 5800













































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды