HP 5800 Скачать руководство пользователя страница 16

Страница: 16 / 396

Port: Local - 179 Remote - 1025

Configured: Active Hold Time: 180 sec Keepalive Time:60 sec

Received : Active Hold Time: 180 sec

Negotiated: Active Hold Time: 180 sec

Peer optional capabilities:

Peer support bgp multi-protocol extended

Peer support bgp route refresh capability

Address family IPv4 Unicast: advertised and received

Received: Total 25 messages, Update messages 1

Sent: Total 30 messages, Update messages 4

Maximum allowed prefix number: 150000

Threshold: 75%

Minimum time between advertisement runs is 30 seconds

Optional capabilities:

ORF advertise capability based on Prefix(type 64):

Local: both

Negotiated: send

Peer Preferred Value: 99

BFD: Enabled

Routing policy configured:

No routing policy is configured

Table 5

Command output

Field Description

Peer

IP address of the peer.

Local

IP address of the local router.

Type BGP

type.

BGP version

Version of BGP that the peer runs.

remote router ID

Router ID of the remote router.

BGP current state

Current status of the BGP session.

Up for

Duration since the peer is established.

BGP current event

Current event of the BGP session.

BGP last state

State that the BGP session was in before transitioning to the
current status.

Port

Local and remote ports of the BGP session.

Configured

Settings of the local timers, including the active hold interval
and keepalive interval.

Received

Received active hold interval.

Negotiated

Negotiated active hold interval and keepalive time.

Peer optional capabilities

Optional capabilities of the peer.

Peer support bgp multi-protocol extended

The peer supports multiprotocol extension.

Содержание 5800













































































































































































































































































































































































































Результаты поиска

Содержание 5800

Отзывы:

Бренды по названию

Популярные бренды

HP 5800, Справочник по командам

Результаты поиска

Содержание 5800

Отзывы:

Бренды по названию

Популярные бренды