manualshive.com logo in svg

HP 5800, Справочник по командам

Поделиться
Скачать
HP 5800 Скачать руководство пользователя страница 294

 

285 

Field Description 

Address family IPv4 Unicast 

IPv4 unicast family capability. 

Address family VPNv4 

IPv4 address group VPNv4 capability. 

Received 

Counts of received messages and received update 
messages. 

Sent 

Counts of sent messages and the number of sent 
update messages. 

Maximum allowed prefix number 

Maximum number of routes that the VPN instance 
supports. 

Threshold Threshold 

value. 

Optional capabilities 

Local optional capabilities. 

ORF advertise capability based on prefix (type 64): 

The ORF address prefix capability is supported. The 
capability value is 64. 

Local 

Indicates whether the local device supports sending 
and receiving Route-refresh packets with ORF 

information. The value can be: 

•

 

both—Supports sending and receiving Route-

refresh messages with ORF information. 

•

 

send—Supports sending Route-refresh messages 

with ORF information. 

•

 

receive—Supports receiving Route-refresh 

messages with ORF information. 

Negotiated 

ORF capability negotiated by the local and remote 
peers. The value can be: 

•

 

send—The local peer can send Route-refresh 

messages with ORF information and the remote 

peer can receive Route-refresh messages with 

ORF information. 

•

 

receive—The local peer can receive Route-refresh 

messages with ORF information and the remote 
peer can send Route-refresh messages with ORF 

information. 

This field is displayed only when the ORF capability 
negotiation is successful. 

Connect-interface 

Whether a source interface is configured for TCP 
connection establishment. 

Peer Preferred Value 

Preference value configured for routes from the peer. 

BFD 

Whether BFD is enabled for the peer. 

 

# Display the log information of the BGP VPNv4 peer whose address is 1.1.1.1. 

<sysname> display bgp vpnv4 vpn-instance vpn1 peer 1.1.1.1 log-info 

 

 Peer : 1.1.1.1 

 

     Date      Time    State Notification 

                             Error/SubError 

Содержание 5800













































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды