manualshive.com logo in svg

HP 5800, Справочник по командам

Поделиться
Скачать
HP 5800 Скачать руководство пользователя страница 40

 

31 

IPv6 MCE configuration commands 

 

 

NOTE: 

•

 

This chapter describes only the commands related to the IPv6 MCE feature. For information about the 
routing protocol configuration commands in the configuration examples, see the 

Layer 3—IP Routing 

Command Reference. 

•

 

For information about IPv6 MPLS L3VPN configuration commands, see the chapter “MPLS L3VPN 
commands.”  

 

display bgp vpnv6 all routing-table 

Description 

Use the 

display bgp vpnv6 all routing-table

 command to display all BGP VPNv6 routing information. 

Syntax 

display bgp vpnv6

 

all

 

routing-table

 [ 

network-address prefix-length

 [ 

longer-prefixes

 ] | 

peer 

ip-address

 

{ 

advertised-routes

 |

 received-routes 

} [ 

statistic

 ] | 

statistic

 ] [ 

|

 { 

begin

 | 

exclude

 | 

include

 } 

regular-

expression 

] 

View 

Any view 

Default level 

1: Monitor 

Parameters 

network-address

: Specifies the IPv6 address of the destination network segment. 

prefix-length

: Specifies the length of the prefix, ranging from 0 to 128.

 

longer-prefixes

: Displays each routing entry that meets the following conditions: 

•

 

Its destination IPv6 address ANDed with the specified prefix equals the specified destination IPv6 
address ANDed with the specified prefix. 

•

 

Its prefix length is shorter than or equal to the specified prefix length. 

•

 

Its prefix length is the longest among the entries meeting the above two conditions. 

peer

 

ip-address

: Displays the routing information sent to or received from the specified peer. 

ip-address

 is 

the IPv4 address of the peer. 

advertised-routes

: Displays the routing information sent to the specified peer. 

received-routes

: Displays the routing information received from the specified peer. 

statistic

: Displays BGP VPNv6 route statistics. 

|

: Filters command output by specifying a regular expression. For more information about regular 

expressions, see the 

Fundamentals Configuration Guide

. 

begin

: Displays the first line that matches the specified regular expression and all lines that follow. 

Содержание 5800













































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды