HP 5800 Скачать руководство пользователя страница 138

Страница: 138 / 396

129

Interface Vlan-interface4

Neighbor Addr: 80.2.1.1

SrcInstance: 832 NbrSrcInstance: 920

PSB Count: 1 RSB Count: 0

Hello Type Sent: REQ Neighbor Hello Extension: ENABLE

SRefresh Enable: NO Reliability Enable: YES

Graceful Restart State: Not Ready

Restart Time: --- Recovery Time: ---

Table 52

Command output

Field Description

Interface

RSVP-TE enabled interface.

Neighbor Addr:

Neighbor address, in the format of X.X.X.X.

SrcInstance

Instance of source Message ID.

NbrSrcInstance

Instance of neighbor Message ID.

PSB Count

Number of path state blocks.

RSB Count

Number of reservation state blocks.

Hello Type Sent

Type of hellos sent to the neighbor: REQ, ACK, or NONE.

Neighbor Hello Extension

State of hello extension: enabled or disabled. This field is displayed
only when hello extension is enabled on the interface.

SRefresh Enable

State of summary refresh: YES for enabled and NO for disabled.

Reliability Enable

State of the reliability function: YES for enabled and NO for disabled.

Graceful Restart State

Neighbor’s GR status: Not Ready, Ready, Restart, or Recovery.
Displayed as --- when not supported by the device.

Restart Time

GR restart interval in seconds.

Recovery Time

GR recovery interval in seconds.

display mpls rsvp-te psb-content

Description

Use the

display mpls rsvp-te psb-content

command to display information about RSVP-TE PSB.

Syntax

display mpls rsvp-te psb-content

ingress-lsr-id lspid

tunnel-id

egress-lsr-id

[

{

begin

exclude

include

}

regular-expression

]

View

Any view

Default level

1: Monitor level

Parameters

ingress-lsr-id

: Specifies the ingress LSR ID.

Содержание 5800













































































































































































































































































































































































































Результаты поиска

Содержание 5800

Отзывы:

Бренды по названию

Популярные бренды

HP 5800, Справочник по командам

Результаты поиска

Содержание 5800

Отзывы:

Бренды по названию

Популярные бренды