HP 5800 Скачать руководство пользователя страница 17

Страница: 17 / 396

Field Description

Peer support bgp route refresh capability

The peer supports route refresh capability.

Address family IPv4 Unicast

IPv4 unicast family capability.

Received

Total number of received messages and the number of
received update messages.

Sent

Total number of sent messages and the number of sent
update messages.

Maximum allowed prefix number

Maximum number of routes that the VPN instance supports.

Threshold Threshold

value.

Minimum time between advertisement runs

Minimum route advertisement interval.

Optional capabilities

Local optional capabilities.

Local

Indicates whether the local device supports sending and
receiving Route-refresh packets with the ORF information.
The value can be:

•

Both: Supports sending and receiving Route-refresh

messages with the ORF information.

•

Send: Supports sending Route-refresh messages with the

ORF information.

•

Receive: Supports receiving Route-refresh messages with

the ORF information.

Negotiated

ORF capability negotiated by the local and remote peers.
The value can be:

•

Send: The local peer can send Route-refresh messages

with the ORF information and the remote peer can
receive Route-refresh messages with the ORF information.

•

Receive: The local peer can receive Route-refresh

messages with the ORF information and the remote peer
can send Route-refresh messages with the ORF

information.

If ORF capability negotiation fails, this field will not be

displayed.

Peer Preferred Value

Weight for the routes from the peer.

Routing policy configured

Routing policy configured.

display bgp vpnv4 vpn-instance routing-table

Description

Use the

display bgp vpnv4 vpn-instance routing-table

command to display the BGP VPNv4 routing

information for a specific VPN instance.

Syntax

display bgp vpnv4 vpn-instance

vpn-instance-name

routing-table

[ [

network-address

[

{

mask

mask-

length

}

[

longer-prefixes

] ] |

as-path-acl

as-path-acl-number

cidr

community

[

aa:nn

]&<1-13> [

no-

advertise

no-export

no-export-subconfed

] * [

whole-match

] |

community-list

{

basic-community-list-

number

[

whole-match

] |

adv-community-list-number

}&<1-16> |

dampened

dampening parameter

Содержание 5800













































































































































































































































































































































































































Результаты поиска

Содержание 5800

Отзывы:

Бренды по названию

Популярные бренды

HP 5800, Справочник по командам

Результаты поиска

Содержание 5800

Отзывы:

Бренды по названию

Популярные бренды