HP 5800 Скачать руководство пользователя страница 255

Страница: 255 / 396

246

Tunnel ID : 0x220020

Table 98

Command output

Field Description

VC ID

Remote VC ID

VC State

Status of the VC

Destination

Destination IP address

Client Intf

Interface connected with the CE

Local Group ID

Local VC group ID, used for the L2VPN VC FEC TLV
field of LDP messages

Remote Group ID

Remote VC group ID, used for the L2VPN VC FEC
TLV field of LDP messages

Tunnel Policy

Tunnel policy configured

Tunnel Type

Type of the tunnel

Tunnel ID

ID of the tunnel

# Display information about Martini VCs received from the remote peer.

<Sysname> display mpls l2vc remote-info

total remote ldp vc : 1

Transport Group Peer Remote Remote C Remote

VC ID ID Addr Encap VC Label Bit MTU

100 0 3.3.3.9 ethernet 1025 0 1500

Table 99

Command output

Field Description

total remote ldp vc

Total number of remote LDP VCs.

Transport VC ID

Remote VC ID.

Group ID

Remote VC group ID, used for the L2VPN VC FEC
TLV field of LDP messages.

Peer Addr

IP address of the peer.

Remote Encap

Encapsulation type of the remote interface.

C Bit

Whether the control word function is enabled or not.
0 means disabled and 1 means enabled.

Remote MTU

MTU of the remote interface.

display mpls l2vpn

Description

Use the

display mpls l2vpn

command to display information about L2VPNs configured on a PE.

If you do not specify a VPN, the command displays information about all L2VPNs.

Содержание 5800













































































































































































































































































































































































































Результаты поиска

Содержание 5800

Отзывы:

Бренды по названию

Популярные бренды

HP 5800, Справочник по командам

Результаты поиска

Содержание 5800

Отзывы:

Бренды по названию

Популярные бренды