HP 5800 Скачать руководство пользователя страница 358

Страница: 358 / 396

349

Field Description

ORF advertise capability based
on prefix (type 64):

Supports the ORF address prefix capability and the capability value is
64.

Local

Indicates whether the local device supports sending and receiving
Route-refresh packets with ORF information. The value can be:

•

both—Supports sending and receiving Route-refresh messages with

ORF information.

•

send—Supports sending Route-refresh messages with ORF

information.

•

receive—Supports receiving Route-refresh messages with ORF
information.

Negotiated

ORF capability negotiated by the local and remote peers. The value
can be:

•

send—The local peer can send Route-refresh messages with ORF

information and the remote peer can receive Route-refresh messages
with ORF information.

•

receive—The local peer can receive Route-refresh messages with

ORF information and the remote peer can send Route-refresh
messages with ORF information.

This field is displayed only when the ORF capability negotiation is
successful.

Connect-interface

Indicates whether a source interface is configured for TCP connection
establishment.

Peer Preferred Value

Preference value configured for the routes from the peer.

BFD

Whether BFD is enabled for the peer.

display bgp vpnv6 all routing-table

Description

Use the

display bgp vpnv6 all routing-table

command to display all BGP VPNv6 routing information.

Syntax

display bgp vpnv6

all

routing-table

[

network-address prefix-length

[

longer-prefixes

] |

peer

ip-address

{

advertised-routes

received-routes

} [

statistic

] |

statistic

] [

{

begin

exclude

include

}

regular-

expression

]

View

Any view

Default level

1: Monitor

Parameters

network-address

: Specifies the IPv6 address of the destination network segment.

prefix-length

: Specifies the length of the prefix, ranging from 0 to 128.

longer-prefixes

: Displays each routing entry that meets the following conditions:

Содержание 5800













































































































































































































































































































































































































Результаты поиска

Содержание 5800

Отзывы:

Бренды по названию

Популярные бренды

HP 5800, Справочник по командам

Результаты поиска

Содержание 5800

Отзывы:

Бренды по названию

Популярные бренды