manualshive.com logo in svg

HP 5800, Справочник по командам

Поделиться
Скачать
HP 5800 Скачать руководство пользователя страница 339

 

330 

By default, no preferred tunnel exists. 
In a tunneling policy, you can configure up to 64 preferred tunnels. 
The tunnel interfaces specified for the preferred tunnels can have the same destination address. The tunnel 

encapsulation type must be MPLS TE.  

Syntax 

preferred-path

 

number

 

interface

 

tunnel

 

tunnel

-

number

 [ 

disable

-

fallback

 ] 

undo

 

preferred

-

path

 

number

 

View 

Tunneling policy view 

Default level 

2: System view 

Parameters 

number

: Specifies the number of the preferred tunnel, ranging from 0 to 63. A smaller number means a 

higher priority. 

interface

 

tunnel

 tunnel-number

: Specifies a tunnel interface for the preferred tunnel. 

tunnel-number 

represents the tunnel interface number, which ranges from 0 to 127. 

disable-fallback

: With this keyword specified, the tunneling policy does not select other paths when this 

preferred tunnel is matched (the tunnel’s destination address and encapsulation type are both matched) 

but is unavailable. 

Examples 

# Tunnel interfaces Tunnel 0, Tunnel 2, and Tunnel 3 have the same destination address 1.1.1.1. Configure 

a tunneling policy 

po1

 for the switch, so that the switch selects tunnels for traffic destined for 1.1.1.1 in this 

order: Tunnel 0, Tunnel 2, Tunnel 3. If all three tunnels are unavailable, tunnel selection is stopped and 

traffic destined for 1.1.1.1 cannot be transmitted. For traffic going to other destinations, the device selects 

tunnels by type, and only one CR-LSP tunnel can be selected. 

<Sysname> system-view 

[Sysname] tunnel-policy po1 

[Sysname-tunnel-policy-po1] preferred-path 0 interface tunnel 0 

[Sysname-tunnel-policy-po1] preferred-path 2 interface tunnel 2 

[Sysname-tunnel-policy-po1] preferred-path 3 interface tunnel 3 disable-fallback 

[Sysname-tunnel-policy-po1] tunnel select-seq cr-lsp load-balance-number 1 

reflect between-clients 

Description 

Use the 

reflect between-clients

 command to enable route reflection between clients. 

Use the 

undo reflect between-clients

 command to disable the function. 

By default, route reflection between clients is enabled. 
If fully meshed interconnections exist between the clients, route reflection is not required. Otherwise, an RR 

is required for routes to be reflected from one client to every other client. 

Содержание 5800













































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды