manualshive.com logo in svg

HP 5800, Справочник по командам

Поделиться
Скачать
HP 5800 Скачать руководство пользователя страница 144

 

135 

 Reservation Incoming Interface: Vlan-interface3 

 Reservation Interface: Vlan-interface3 

 Message ID : 2 

 Filter Spec Information- 

   The filter number: 1 

   Ingress LSR ID: 19.19.19.19    Local LSP ID: 1      OutLabel: 3 

   Graceful Restart State: Stale 

 RRO Information- 

 RRO-Flag is 

   RRO-CType: IPV4   RRO-IPAddress: 101.101.101.2      RRO-IPPrefixLen: 32 

 FlowSpec Information- 

   Token bucket rate: 2500.00 

   Token bucket size: 0.00 

   Peak data rate: 0.00 

   Minimum policed unit: 0 

   Maximum packet size: 0 

   Bandwidth guarantees: 0.00 

   Delay guarantees: 0 

   Qos Service is Controlled 

 Resv Message arrive on Vlan-interface3 from NHOP 101.101.101.2 

 Graceful Restart State: Stale 

Table 56

 

Command output 

Field Description 

Tunnel Dest 

Tunnel destination, in the format of X.X.X.X. 

Tunnel Ext ID 

Tunnel extension (ingress LSR ID), in the format of X.X.X.X. 

Next Hop 

Next hop address, in the format of X.X.X.X. 

Reservation Style 

Reservation style: SE or FF. 

Reservation Interface 

Reservation interface name. 

Reserve Incoming 
Interface 

Incoming interface where the Resv message was received. 

Message ID 

Message ID of the Refresh Reduction message. 

Filter Spec Information 

Filter specifications. 

The filter number 

Number of filters. 

Ingress LSR ID 

Ingress LSR ID, in the format of X.X.X.X. 

Out Label 

Outgoing label. 

RRO Information 

Information about route recording. 

RRO-C Type 

Type of route recording. 

RRO-IP Address 

IP address of recorded route in the format of X.X.X.X. 

RRO-IPPrefixLen 

IP prefix length of recorded route. 

Flow Spec information 

Flow specifications. 

Token Bucket rate 

Token bucket rate (in kbps), a traffic parameter. 

Содержание 5800













































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды