HP 5800 Скачать руководство пользователя страница 279

Страница: 279 / 396

270

MPLS L3VPN configuration commands

NOTE:

•

For information about the BGP L2VPN address family and the VPLS address family, see the

MPLS

Configuration Guide.

•

The HP 5820X switch series do not support MPLS L3VPN.

default local-preference (BGP-VPNv4 subaddress family view)

Description

Use the

default local-preference

command to set the default value of the local preference.

Use the

undo default local-preference

command to restore the default.

By default, the default value of the local preference is 100.

Syntax

default local-preference

value

undo default local-preference

View

BGP-VPNv4 subaddress family view

Default level

2: System level

Parameters

value

: Specifies the default value for the local preference, ranging from 0 to 4,294,967,295. A greater

value represents a higher priority.

Examples

# Devices A and B are connected to the outside AS. In BGP-VPNv4 subaddress family view of Device B,

set the default local preference of Device B to 180, so that when a destination in the outside AS can be

reached through both A and B, the BGP VPN-IPv4 route going through B to the destination is preferred.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv4-family vpnv4

[Sysname-bgp-af-vpnv4] default local-preference 180

default med (BGP-VPNv4 subaddress family view)

Description

Use the

default med

command to set the default system MED.

Use the

undo default med

command to restore the default.

Содержание 5800













































































































































































































































































































































































































Результаты поиска

Содержание 5800

Отзывы:

Бренды по названию

Популярные бренды

HP 5800, Справочник по командам

Результаты поиска

Содержание 5800

Отзывы:

Бренды по названию

Популярные бренды