HP 5800 Скачать руководство пользователя страница 45

Страница: 45 / 396

BGP last state: OpenConfirm

Port: Local - 179 Remote - 1024

Configured: Active Hold Time: 180 sec Keepalive Time: 60 sec

Received : Active Hold Time: 180 sec

Negotiated: Active Hold Time: 180 sec Keepalive Time:60 sec

Peer optional capabilities:

Peer support bgp multi-protocol extended

Peer support bgp route refresh capability

Address family IPv6 Unicast: advertised and received

Received: Total 4 messages, Update messages 2

Sent: Total 6 messages, Update messages 3

Maximum allowed prefix number: 4294967295

Threshold: 75%

Minimum time between advertisement runs is 30 seconds

Optional capabilities:

Route refresh capability has been enabled

Peer Preferred Value: 0

Routing policy configured:

No routing policy is configured

Table 15

Command output

Field Description

BGP Peer

IPv6 address of the BGP peer.

remote AS

AS number of the peer.

Type BGP

type.

BGP version

Version of BGP that the peer runs.

remote router ID

Router ID of the peer.

BGP current state

Current state of the BGP session.

Up for

Duration since the peer is established.

BGP current event

Current event of the BGP session.

BGP last state

State that the BGP session was in before transitioning to the current
state.

Port

Local and remote ports of the BGP session.

Configured

Settings of the local timers, including the active hold interval and
keepalive interval.

Received

Received active hold interval.

Negotiated

Negotiated active hold interval.

Peer optional capabilities

Optional capabilities of the peer.

Peer support bgp multi-protocol
extended

The peer supports multiprotocol extension.

Содержание 5800













































































































































































































































































































































































































Результаты поиска

Содержание 5800

Отзывы:

Бренды по названию

Популярные бренды

HP 5800, Справочник по командам

Результаты поиска

Содержание 5800

Отзывы:

Бренды по названию

Популярные бренды