manualshive.com logo in svg

HP 5800, Справочник по командам

Поделиться
Скачать
HP 5800 Скачать руководство пользователя страница 60

 

51 

•

 

Advertises label bindings for FEC 10.2.1.0/24 to the LDP peer with the LSR ID 4.4.4.9. 

•

 

Does not advertise label bindings of other segments to any peers. 

<Sysname> system-view 

[Sysname] ip ip-prefix prefix-to-C permit 10.1.1.0 24 

[Sysname] ip ip-prefix prefix-to-D permit 10.2.1.0 24 

[Sysname] ip ip-prefix peerC permit 3.3.3.9 32 

[Sysname] ip ip-prefix peerD permit 4.4.4.9 32 

[Sysname] mpls ldp 

[Sysname-mpls-ldp] advertise-label ip-prefix prefix-to-C peer peer-C 

[Sysname-mpls-ldp] advertise-label ip-prefix prefix-to-D peer peer-D 

bfd enable 

Description 

Use the 

bfd enable

 command to enable BFD to check the connectivity of the LSPs of the specified FEC.  

Use the 

undo

 

bfd enable

 command to disable BFD for the LSPs of the specified FEC.  

By default, BFD is not configured for connectivity check of LSPs.  
You need to enable LSP verification by using the 

mpls lspv

 command before executing the 

bfd enable

 

command. 
The BFD session parameters are those configured on the loopback interface whose IP address is 

configured as the MPLS LSR ID. The BFD packets will use the MPLS LSR ID as the source address. 
Therefore, before enabling BFD for an LSP, configure an IP address for the loopback interface and 

configure the MPLS LSR ID as the IP address of the loopback interface. You can also configure BFD 

session parameters for the loopback interface as needed. 

Syntax 

bfd enable 

destination-address

 

mask-length

 

[

 nexthop

 

nexthop-address 

[

 discriminator local 

local-id

 

remote

 

remote-id 

] ] 

undo bfd enable 

destination-address

 

mask-length 

[ 

nexthop

 

nexthop-address 

]

 

View 

MPLS LSPV view 

Default level 

2: System level 

Parameters 

destination-address

: Specifies the destination address of the FEC.  

mask-length

: Specifies the destination address mask of the FEC, ranging from 0 to 32.  

nexthop 

nexthop-address

: Specifies the next hop address of the FEC. If you specify the FEC next hop, the 

BFD inspects the specified LSP. If you do not specify it, the BFD detects all LSPs for the FEC.  

discriminator

: Specifies the discriminator values of the BFD session. 

 

local

 local-id

: Specifies the local discriminator value of the BFD session. The value ranges from 1 to 32. 

 

remote

 remote-id

: Specifies the remote discriminator value of the BFD session. The value ranges from 1 to 

4,294,967,295. 

Содержание 5800













































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды