HP 5800 Скачать руководство пользователя страница 291

Страница: 291 / 396

282

Table 118

Command output

Field Description

Peer

IP address of the peer.

Local

IP address of the local router.

Type BGP

type.

BGP version

Version of BGP that the peer runs.

remote router ID

Router ID of the remote router.

BGP current state

Current status of the BGP session.

Up for

Duration since the peer is established.

BGP current event

Current event of the BGP session.

BGP last state

State that the BGP session was in before
transitioning to the current status.

Port

Local and remote ports of the BGP session.

Configured

Settings of the local timers, including the active hold
interval and keepalive interval.

Received

Received active hold interval.

Negotiated

Negotiated active hold interval.

Peer optional capabilities

Optional capabilities of the peer.

Peer support bgp multi-protocol extended

The peer supports multiprotocol extension.

Peer support bgp route refresh capability

The peer supports route refresh capability.

Address family IPv4 Unicast

IPv4 unicast family capability.

Received

Counts of received messages and received update
messages.

Sent

Counts of sent messages and sent update messages.

Maximum allowed prefix number

Maximum number of routes that the VPN instance
supports.

Threshold Threshold

value.

Optional capabilities

Local optional capabilities.

ORF advertise capability based on prefix (type 64):

ORF address prefix capability is supported. The
capability value is 64.

Local

Indicates whether the local device supports sending
and receiving Route-refresh packets with ORF

information. The value can be:

•

both—Supports sending and receiving Route-

refresh messages with ORF information.

•

send—Supports sending Route-refresh messages

with ORF information.

•

receive—Supports receiving Route-refresh

messages with ORF information.

Содержание 5800













































































































































































































































































































































































































Результаты поиска

Содержание 5800

Отзывы:

Бренды по названию

Популярные бренды

HP 5800, Справочник по командам

Результаты поиска

Содержание 5800

Отзывы:

Бренды по названию

Популярные бренды