HP 5800 Скачать руководство пользователя страница 193

Страница: 193 / 396

184

Parameters

-a

source-ip

: Specifies the source IP address of MPLS Echo Request messages. By default, the MPLS LSR ID

is used as the source address of MPLS Echo Request messages.

-exp

exp-value

: Specifies the EXP value of the label.

exp-value

ranges from 0 to 7 and defaults to 0.

-h

ttl-value

: Specifies the TTL value to be carried by an MPLS Echo Request message.

ttl-number

is ranging

from 1 to 255 and defaults to 30.

-m

wait-time

: Specifies the interval for performing LSP tracert.

wait-time

is ranging from 15 to 120 and

defaults to 60, in minutes.

-t

time-out

: Specifies the timeout time for waiting for the response of an MPLS Echo Request message.

time-out

is ranging from 0 to 65,535 and defaults to 2000, in milliseconds.

-u

retry-attempt

: Specifies the maximum number of times that MPLS Echo Request messages can be sent if

no response is received.

retry-attempt

ranges from 1 to 9 and defaults to 3.

Examples

# Enable periodic LSP tracert for the MPLS TE tunnels on tunnel interface Tunnel 0.

<Sysname> system-view

[Sysname] interface tunnel 0

[Sysname-Tunnel0] mpls te periodic-tracert

mpls te priority

Description

Use the

mpls te

priority

command to assign a setup priority and holding priority to the MPLS TE tunnel.

Use the

undo mpls te priority

command to restore the default.

By default, both setup and holding priorities of TE tunnels are 7.
To avoid flapping caused by improper preemptions between TE tunnels, the setup priority of an MPLS TE

tunnel should not be set higher than its holding priority.

Syntax

mpls te priority

setup-priority

[

hold-priority

]

undo mpls te priority

View

Tunnel interface view

Default level

2: System level

Parameters

setup-priority

: Specifies the setup priority of the tunnel, ranging from 0 to 7. A lower numerical number

indicates a higher priority.

hold-priority

: Specifies the holding priority of the tunnel, ranging from 0 to 7. A lower numerical number

indicates a higher priority. If not configured, it is the same as the setup priority.

Examples

# Set the setup and holding priorities of TE tunnel 0 to 1.

Содержание 5800













































































































































































































































































































































































































Результаты поиска

Содержание 5800

Отзывы:

Бренды по названию

Популярные бренды

HP 5800, Справочник по командам

Результаты поиска

Содержание 5800

Отзывы:

Бренды по названию

Популярные бренды