Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 230

Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 81

81

Module

A: Enter
Quantity

B: Max
Current
@ 5V

C: Max
Current
@ 24V

D:
Calculate
5V current
(D = A * B)

E:
Calculate
24V
current (E
= A * C)

Total mA
@ 5V - ( )

Total mA @
24V - ( )

* The field device is powered by external 24 V power supply. For more information,
see

Universal Input/Output Module

on section.

Environmental considerations

The product is only used indoors. The CPM must be mounted in
suitable equipment enclosures. That is, all components such as the
Redundant Controller Rack and I/O rack manufactured by Honeywell
must be mounted in approved furniture designed for industrial
applications.

Consideration should be given to the installation so that the potential
for the build-up of static electricity is minimized or eliminated.

Table 5-8: Environmental specifications

Item

Description

Operating temperature

0 to 60 °C

Storage and transportation
temperature

-40 to 85 °C

Ambient Relative Humidity

5% to 95% relative humidity (non-condensing)

Vibration (Operative)

IEC 60068-2-6 Sinusoidal (5 to 8.4 Hz) 3.5mm /
(8.4 to 150 Hz) 1.0 g; 1 octave/min, 10 cycles per
axis, 3 axes.

Shock (Operative)

Half-sine, 15g peak / 11 ms duration, 6 directions

Protection against corrosive
atmospheres (for offshore
installations)

ANSI/ISA S71.04 Class G3

Altitude

2000 meters

«
...
79
80
81
82
83
...
»

Содержание ControlEdge 900 platform







































































































































































































































Отзывы:

Нет отзывов