Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 7

Страница: 7 / 230

CHAPTER

ABOUT THIS GUIDE

Scope

This guide describes how to set up the ControlEdge 900 platform and
install UOC or PLC.

Revision history

Revision Date

Description

September
2016

Initial release of document

November
2016

Update for PLC R130.2 Release including:

Delete the Self-powered 3–wire transmitter for UIO AI,
and updated Self-powered 4-wire transmitter for UIO AI.

Add 900RTP-H1xx RTP Cable

Add MOXA Unmanaged Ethernet Switch EDS-308 and
EDS-316-MM-SC.

April 2017

Update for the PLC R140 Release including:

Five new I/O modules

Add new RTP and RTP Cables

New Terminal Blocks

New accessory parts

June 2017

Update for PLC. Adding the following items:

Add UIO wiring limitation and hardware version
comparison

Add RTP dimension for installing

September
2017

Added UOC information (for Experion R505 release)

November

Update for UOC network topologies

Содержание ControlEdge 900 platform







































































































































































































































Результаты поиска

Содержание ControlEdge 900 platform

Отзывы:

Honeywell ControlEdge 900 platform, Руководство по планированию и установке оборудования, Страница: 7 / 230

Результаты поиска

Содержание ControlEdge 900 platform

Отзывы: