Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 230

Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 40

Installation and maintenance practices for the UOC’s downlink
EtherNet/IP network generally follow those described in (

EtherNet IP

User's Guide

) for topology 2, “C300 Through EIM To EtherNet/IP”.

Additional considerations for components that connect to the
EtherNet/IP network are summarized in the following table.

Component
Type

Comments

ControlEdge
UOC CPM

The UOC CPM connects to a downlink EtherNet/IP network through
its ETH3 and ETH4 ports. Important properties of UOC CPM
communications on the downlink network are configured on the
UOC Platform Block in Control Builder. This includes configuration
of the UOC DHCP server for assigning EPM IP addresses. It also
includes Downlink Network Configuration to Non-redundant.

ControlEdge
900 I/O
Racks with
EPMs

When 900 I/O is used, the EPM in the I/O rack serves the role of
communication gateway into the I/O rack. When an EPM is
connected to an EtherNet/IP network, its ETH1 port is connected to
the ETAP while its ETH2 port is left disconnected. Before it is inserted
into its slot, the 100x rotary switch on the EPM board must be set to
indicate the type of network connectivity in use. This is done by
setting it to position 4. The IP address of the EPM is assigned by the
UOC CPM based on the module number set on the 10X and 1x rotary
switches. These switches must also be set before the EPM is inserted
into its slot.

EtherNet/IP
TAPs (ETAPs)

UOC systems use redundancy boxes called ETAPs for connectivity to
downlink DLR rings. For further information on the use of ETAPs, see

EtherNet IP User's Guide_EPDOC-X399-en-510A.pdf

.

ControlLogix
PLC

UOC can communicate with Rockwell Allen Bradley ControlLogix
PLCs by passing instances of User Defined Types (UDTs). References
to ControLogix data are created in Experion Control Builder with the
aid of tag names provided by the Matrikon Allen Bradley OPC server
or by export of ControlLogix tag names from the Rockwell Allen
Bradley Studio 5000 designer tool. ControlLogix PLCs on a UOC’s
downlink EtherNet/IP network must always use static IP address
assignments. For information on the configuration of ControlLogix
communications, see

EtherNet IP User's Guide_EPDOC-X399-en-

510A.pdf

.

EtherNet/IP
I/O and
Devices

UOC supports a set of EtherNet/IP devices with pre-populated CEE
block types in Experion Control Builder (CB). In addition, CB provides
the Parameter Definition Editor (PDE) tool which allows for the
integration of new EtherNet/IP I/O and devices independent of
Experion release. Although some third party EtherNet/IP devices
support IP address assignment from a network resident DHCP
server, this feature cannot be used when the EtherNet/IP network

40

«
...
38
39
40
41
42
...
»

Содержание ControlEdge 900 platform







































































































































































































































Отзывы:

Нет отзывов