Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 23

Страница: 23 / 230

Item Description

ETH1 and ETH2 host ports to PC applications and/or other CPMs, or other
devices.

ETH3 and ETH4 ports connect to the Ethernet ports of EPM, switch (for star
topology), or CPM.

Ethernet LED status indicators for communications functions. For more
information, see

section.

CAUTION: Do not remove or insert the Ethernet connection when
the CPM is powered unless the area is known to be non-
hazardous.

PLC-CPM mode switch

There are four mode switch positions on CPM: STOP, RUN, and two
REMOTE positions which are identical.

Figure 3-4: Mode switch on CPM

The switch can be rotated in a clockwise or counter-clockwise fashion
in order to engage the four switch positions. When the mode switch is

Содержание ControlEdge 900 platform







































































































































































































































Результаты поиска

Содержание ControlEdge 900 platform

Отзывы:

Honeywell ControlEdge 900 platform, Руководство по планированию и установке оборудования, Страница: 23 / 230

Результаты поиска

Содержание ControlEdge 900 platform

Отзывы: