Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 10

Страница: 10 / 230

Item

Description

ControlEdge
UOC

ControlEdge 900 controllers running the Honeywell control execution
environment (CEE) configured with Experion Control Builder.

Special Terms

The following table describes the commonly used industry-wide and
Honeywell-specific terminology:

Terminology Description

Analog Input

Analog Output

CEE

Control Execution Environment (Experion)

ControlEdge
900

A family of controller and I/O hardware which can be assembled to
create PLC or UOC systems.

ControlEdge
Builder

Software configuration tool for PLC.

Control
Builder

Experion Control Builder, configuration tool for UOC.

COTS

Commercial Off the Shelf

CPM

Control Processor Module (commonly referred to as the controller).
The ControlEdge 900 CPM, can be loaded with PLC firmware to
become the PLC or with UOC-CPM firmware to become the UOC-
CPM.

DCS

Distributed Control System

Digital Input

DLR

Device Level Ring

Digital Output

EPM

Expansion Processor Module (used to connect multiple I/O racks to
the Control Processor Module)

Expansion
I/O rack

I/O rack with EPM installed

Ethernet/IP

EtherNet/IP™ is a trademark protocol owned by ODVA.

Chapter 1 - About this guide

Содержание ControlEdge 900 platform







































































































































































































































Результаты поиска

Содержание ControlEdge 900 platform

Отзывы:

Honeywell ControlEdge 900 platform, Руководство по планированию и установке оборудования, Страница: 10 / 230

Результаты поиска

Содержание ControlEdge 900 platform

Отзывы: